Cisco
in [Network]
|
Solution to ARP spoofing on 3560 and 2960 switches please Hi, We have a Cisco6500 as the backbone and a 3560 as router in each of the edges (buildings). Connected to 3560's there are 2960's. Each of the buildings have their own VLAN/subnets. Recently we found out that infected PC's in every building are sending strange ARP packets and announcing themselves as the ga... 20 Apr 2008 14:00
802.1x with ACS and Third Party Switch I want do use the Cisco ACS for 802.1x authentication with a Third Party Switch (Alcatel). With a Cisco switch everything works fine. This is also true with the Alcatel Switch as long as I set the Radius Type in the ACS to IETF. Put for some purpose I need VSAs (RADIUS Vendor-Specific Attributes). So I created my ... 8 Apr 2008 10:48
PIX 501 6.3 Hello, I am not sure where I am going wrong here, but when I add the following 4 lines to my configuration, I loose the outbound access and gain web and smtp server publishing. Could somebody tell me why and how to fix it access-list inbound permit tcp any host 67.81.19.32 eq https access-list inbound permi... 8 Apr 2008 10:48
Cisco 878 Hi all I'm having trouble with an 878 SHDSL modem My startup config for the controller is controller DSL 0 mode atm line-term cpe line-mode auto dsl-mode shdsl symmetric annex B line-rate 2048 Yet when I start the modem up the line rate changes to 1152 Show running controller DSL 0 mode a... 10 Apr 2008 07:46
VPN Errors on multilink T1 - but inly for DHCP and not staticNAT users? lwpowers(a)gmail.com schrieb: I have a Cisco 1700 router with dual WIC/T1's LAN users are assigned NAT IP addresses from the Cisco 1700 via DHCP from 10.0.0.100 to 10.0.0.200. 10.0.0.2 - 10.0.0.15 are 1:1 configured to our 16 internet routable IP addresses. Users who receive an IP address vi... 8 Apr 2008 04:21
HW & SW VPN client -- need routing workaround We have a 3005 concentrator with 3002s at three branches of a clinic. Their local subnets are 192.168.0.0, 192.168.1.0 and 192.168.3.0. I live on a family farm and connect to a satellite router that is maintained by my daughter-in-law's employer, so I can't change the 192.168.0.0 subnet I'm on. So, I can get i... 9 Apr 2008 00:31
Pix 506e w/5 static outside IPs - How to create a rule to allowALL tcp/udp traffic from one outside IP to an internal IP (for an internalrouter/NAT with it's own subnet) Aceman wrote: In news:4MiKj.162061$pM4.7003(a)pd7urf1no, Walter Roberson <roberson(a)hushmail.com> typed: You mean the actual Verizon source IP? Yes. With "permit ip any", *anyone* on the 'Net would be allowed to send most -anything- to your FIOSTV. And they will, they will. For example, google searc... 8 Apr 2008 12:26
Pix as router? I have a pix (well several) and just want a router (just one) for a private link. Pix is plenty man enough for the job and I don't need GRE or any dynamic routing. Am I likely to regret it? If I set inside and outside to secutrity level 0 and/or put permit ip any any on the interfaces am I likely to run into ... 8 Apr 2008 21:18
FWSM - SAP timeout ? Hi, I see some conn's in my FWSM that screens my SAP servers. some of them towards port TCP/3321. This is normal. But some of these conn's I see with Conn-Timeout after 20 sec ! and 264 bytes each time. Since its 20 sec timeout I know it is not the firewall timeout that are in action, so what is this ? ... 7 Apr 2008 15:42
2610xm issue :/ Hi guys after loading a new IOS onto my 2610xm this is the message I got. the ios before did not work properly i guess and it kept saying nvram cannot write and that type of stuff. I figured if i instal a new ios it would fix the problem but even afterwards i get this message 00:04:43: %SYS-5-RELOAD: Reload requ... 8 Apr 2008 13:15 |