LabView

??? Re: TDMS Timestamp Decoding - Help!!
hello,I run your code,but some error occur: ??? Attempt to reference field of non-structure array. Error in ==> convertTDMS at 218                    ssamples=ob.(cname).nsamples;   what is the problem? I run the ... 6 May 2008 23:25

Just ATR only is not coming
Dear Champions, In my application, everything is fine. 1) sCardEstablishContext works fine 2) sCardListReadersA showing correct name of my reader 3) sCardConnectA give proper mode(1) and protocol(1) values 4) sCardStatusA ???????????? There is the problem. It gives state(6 - reset) and protocol(1). That is co... 7 May 2008 12:35

SR830 data storage
I am planning to develop the C-V measurement set-up of MOS capacitors using SR830 lock-in amplifier. I am using 2 instruments in my experiment. One is the source meter with the help of which I am providing a linear voltage ramp from -10 to +10 volts to the MOS capacitor.I want to store  the corresponding  val... 6 May 2008 23:25

PSK simulation exercise
Hi everyone,                     anyone knows how to modify this simulation exercise to show PSK modulation and constellation diagram? Thanks! Proj_PSK.vi: http://forums.ni.com/attachments/ni/170/321218/1/Proj_PSK.vi ... 7 May 2008 12:35

??? Re: ??? Re: ??? Re: Can't get LabView 8.2 working on Leopard
Dear Van L I guess that I have no further question at the present time. :) Thanks for your care.Yu-Hung ... 6 May 2008 23:25

Updating filter setting in Hottinger HBM software CATMAN frominside LABVIEW
Hi Hobart, &nbsp; Could you please describe a bit more as to&nbsp;how you are accessing the instrument&nbsp;or if you're using any drivers from the <a href="http://www.ni.com/devzone/idnet/" target="_blank">Instrument Driver Network</a>? &nbsp; &nbsp; ... 6 May 2008 23:25

7.1 after repair unregistered...
After repair of the 7.1.1 runtime engine, splash screen said unregistered. Edited the registry to put in serial number. Now the serial number is on the splash screen and it says unregistered too. What gives? Does this matter? Is this whole installation going to stop working? ... 6 May 2008 23:25

Necessary Matlab compiler options to integrate generated dll inVI
I've never actually done this, but in searching the forums I found a number of helpful posts: &nbsp; <a href="http://forums.ni.com/ni/board/message?board.id=180&amp;message.id=19209&amp;requireLogin=False" target="_blank">http://forums.ni.com/ni/board/message?board.id=180&amp;message.id=19209&amp;requireLogin=False</... 6 May 2008 23:25

Using NI 9481 and 9474 to control digital output and relays
So...&nbsp; I am controlling several values by writing to 9474 (Valve Port A) while also switching a (one) relay on 9481 (Pump Relay).&nbsp;&nbsp; I initially built a separate vi with the "Pump Relay" which worked fine.&nbsp; The attached vi w/o "Pump Relay" also works fine.&nbsp; When the two are combined, the "Pump R... 6 May 2008 23:25

Device independent application protocol; is there anequivalent to an abstract base class?
Hi Terry, Other people are going to have to help me out on this one.&nbsp; I think data sockets are close to what you want.&nbsp; You start by declaring what protocol you want to use (like, tcp or udp).&nbsp; Then it send the message out on the default communication bus.&nbsp; For something more specific, you might nee... 6 May 2008 23:25