MSP430 - IAR vs gcc
in [Embedded]
|
From: Baxter on 1 Jul 2005 11:35 Having an IDE to work with is great, but is IAR worth the bucks? 1 - will it save that much time? Including learning time - especially for someone used to IDEs like Visual Studio? 2 - are there opportunities with the MSP430 to earn back the cost of IAR? 3 - are there any good IDE front ends for mspgcc? (and the debugger) -- ------------------------------------------------------------------------- Free software - Baxter Codeworks www.baxcode.com -------------------------------------------------------------------------
From: andreas.bellgardt on 1 Jul 2005 13:00 Hi Baxter, I looked at the IAR IDE and used a 2kB restricted version only a short time. I think the full version is too expensive. Then, I took the GNU tools from mspgcc.sourceforge.net - very nice tool! If you know the GNU tools, no problem. If you need an IDE, take a look at www.eclipse.org. There is a plugin for MSP430 and C: http://homepage.hispeed.ch/py430/mspgcc/ It takes some time to setup up, but then you have an professionall IDE for free! Regards, Andreas
From: Rich Webb on 1 Jul 2005 14:08 On Fri, 1 Jul 2005 08:35:47 -0700, "Baxter" <lbax02.spamguard(a)baxcode.com> wrote: >Having an IDE to work with is great, but is IAR worth the bucks? >1 - will it save that much time? Including learning time - especially for >someone used to IDEs like Visual Studio? >2 - are there opportunities with the MSP430 to earn back the cost of IAR? >3 - are there any good IDE front ends for mspgcc? (and the debugger) Imagecraft also has a pretty good C compiler for the MSP430 family. It has an IDE, application builder, project manager, etc. There's a time limited full version (that reverts to code-limited after so many days) available at www.imagecraft.com/software I mostly use their AVR compiler but have & use their 430 and ARM products as well. Quite a bit less expensive than the IAR and none of the "well, you can get the bug-fix release if you pay the last two year's annual maintenance fees" that we ran into when I was an IAR customer. -- Rich Webb Norfolk, VA
From: Markus Mandl on 1 Jul 2005 14:30 Baxter wrote: ..... > 3 - are there any good IDE front ends for mspgcc? (and the debugger) KDevelop - www.kdevelop.org Regards Markus
From: Baxter on 1 Jul 2005 17:36
I may end up going this direction as I program for Palm too. The general consensus is that the Palm implementation for Eclipse (PODS) is proceeding well but is not quite ready for prime time. (I'm using CodeWarrior) For right now, the free IAR works as my program comes in at less than 1.5K and revisions I'm considering would make it even smaller. If there's Consulting Opportunities, however, then it becomes a different ballgame. -- ------------------------------------------------------------------------- Free software - Baxter Codeworks www.baxcode.com ------------------------------------------------------------------------- <andreas.bellgardt(a)web.de> wrote in message news:1120237229.101031.46320(a)g49g2000cwa.googlegroups.com... > Hi Baxter, > I looked at the IAR IDE and used a 2kB restricted version only a short > time. I think the full version is too expensive. Then, I took the GNU > tools from mspgcc.sourceforge.net - very nice tool! > If you know the GNU tools, no problem. If you need an IDE, take a look > at www.eclipse.org. > There is a plugin for MSP430 and C: > http://homepage.hispeed.ch/py430/mspgcc/ > It takes some time to setup up, but then you have an professionall IDE > for free! > > Regards, > Andreas > |