From: Thibaut Girka on
Signed-off-by: Thibaut Girka <thib(a)sitedethib.com>
---
drivers/mmc/host/Kconfig | 11 +
drivers/mmc/host/Makefile | 1 +
drivers/mmc/host/glamo-mci.c | 985 ++++++++++++++++++++++++++++++++++++++++++
3 files changed, 997 insertions(+), 0 deletions(-)
create mode 100644 drivers/mmc/host/glamo-mci.c

diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
index f06d06e..b28bf7c 100644
--- a/drivers/mmc/host/Kconfig
+++ b/drivers/mmc/host/Kconfig
@@ -365,6 +365,17 @@ config MMC_S3C_PIODMA

endchoice

+config MMC_GLAMO
+ tristate "Glamo S3C SD/MMC Card Interface support"
+ depends on MFD_GLAMO && MMC && REGULATOR
+ select CRC7
+ help
+ This selects a driver for the MCI interface found in
+ the S-Media GLAMO chip, as used in Openmoko
+ neo1973 GTA-02.
+
+ If unsure, say N.
+
config MMC_SDRICOH_CS
tristate "MMC/SD driver for Ricoh Bay1Controllers (EXPERIMENTAL)"
depends on EXPERIMENTAL && PCI && PCMCIA
diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
index e30c2ee..9d03382 100644
--- a/drivers/mmc/host/Makefile
+++ b/drivers/mmc/host/Makefile
@@ -30,6 +30,7 @@ ifeq ($(CONFIG_OF),y)
obj-$(CONFIG_MMC_SPI) += of_mmc_spi.o
endif
obj-$(CONFIG_MMC_S3C) += s3cmci.o
+obj-$(CONFIG_MMC_GLAMO) += glamo-mci.o
obj-$(CONFIG_MMC_SDRICOH_CS) += sdricoh_cs.o
obj-$(CONFIG_MMC_TMIO) += tmio_mmc.o
obj-$(CONFIG_MMC_CB710) += cb710-mmc.o
diff --git a/drivers/mmc/host/glamo-mci.c b/drivers/mmc/host/glamo-mci.c
new file mode 100644
index 0000000..f07ad09
--- /dev/null
+++ b/drivers/mmc/host/glamo-mci.c
@@ -0,0 +1,985 @@
+/*
+ * linux/drivers/mmc/host/glamo-mmc.c - Glamo MMC driver
+ *
+ * Copyright (C) 2007 Openmoko, Inc, Andy Green <andy(a)openmoko.com>
+ * Copyright (C) 2009, Lars-Peter Clausen <lars(a)metafoo.de>
+ * Based on S3C MMC driver that was:
+ * Copyright (C) 2004-2006 maintech GmbH, Thomas Kleffel <tk(a)maintech.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <linux/mmc/mmc.h>
+#include <linux/mmc/sd.h>
+#include <linux/mmc/host.h>
+#include <linux/platform_device.h>
+#include <linux/irq.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/workqueue.h>
+#include <linux/crc7.h>
+#include <linux/scatterlist.h>
+#include <linux/io.h>
+#include <linux/regulator/consumer.h>
+#include <linux/err.h>
+#include <linux/mfd/glamo.h>
+#include <linux/mfd/glamo-core.h>
+#include <linux/mfd/glamo-regs.h>
+
+struct glamo_mci_host {
+ struct glamo_mmc_platform_data *pdata;
+ struct platform_device *pdev;
+ struct glamo_core *core;
+ struct mmc_host *mmc;
+ struct resource *mmio_mem;
+ struct resource *data_mem;
+ void __iomem *mmio_base;
+ uint16_t __iomem *data_base;
+
+ unsigned int irq;
+
+ struct regulator *regulator;
+ struct mmc_request *mrq;
+
+ unsigned int clk_rate;
+
+ unsigned short vdd;
+ char power_mode;
+
+ unsigned char request_counter;
+
+ struct workqueue_struct *workqueue;
+ struct work_struct read_work;
+};
+
+static void glamo_mci_send_request(struct mmc_host *mmc,
+ struct mmc_request *mrq);
+static void glamo_mci_send_command(struct glamo_mci_host *host,
+ struct mmc_command *cmd);
+
+/*
+ * Max SD clock rate
+ *
+ * held at /(3 + 1) due to concerns of 100R recommended series resistor
+ * allows 16MHz @ 4-bit --> 8MBytes/sec raw
+ *
+ * you can override this on kernel commandline using
+ *
+ * glamo_mci.sd_max_clk=10000000
+ *
+ * for example
+ */
+
+static int sd_max_clk = 21000000;
+module_param(sd_max_clk, int, 0644);
+
+/*
+ * Slow SD clock rate
+ *
+ * you can override this on kernel commandline using
+ *
+ * glamo_mci.sd_slow_ratio=8
+ *
+ * for example
+ *
+ * platform callback is used to decide effective clock rate, if not
+ * defined then max is used, if defined and returns nonzero, rate is
+ * divided by this factor
+ */
+
+static int sd_slow_ratio = 8;
+module_param(sd_slow_ratio, int, 0644);
+
+/*
+ * Post-power SD clock rate
+ *
+ * you can override this on kernel commandline using
+ *
+ * glamo_mci.sd_post_power_clock=1000000
+ *
+ * for example
+ *
+ * After changing power to card, clock is held at this rate until first bulk
+ * transfer completes
+ */
+
+static int sd_post_power_clock = 1000000;
+module_param(sd_post_power_clock, int, 0644);
+
+
+static inline void glamomci_reg_write(struct glamo_mci_host *glamo,
+ uint16_t reg, uint16_t val)
+{
+ writew(val, glamo->mmio_base + reg);
+}
+
+static inline uint16_t glamomci_reg_read(struct glamo_mci_host *glamo,
+ uint16_t reg)
+{
+ return readw(glamo->mmio_base + reg);
+}
+
+static void glamomci_reg_set_bit_mask(struct glamo_mci_host *glamo,
+ uint16_t reg, uint16_t mask,
+ uint16_t val)
+{
+ uint16_t tmp;
+
+ val &= mask;
+
+ tmp = glamomci_reg_read(glamo, reg);
+ tmp &= ~mask;
+ tmp |= val;
+ glamomci_reg_write(glamo, reg, tmp);
+}
+
+static void glamo_mci_reset(struct glamo_mci_host *host)
+{
+ glamo_engine_reset(host->core, GLAMO_ENGINE_MMC);
+
+ glamomci_reg_write(host, GLAMO_REG_MMC_WDATADS1,
+ (uint16_t)(host->data_mem->start));
+ glamomci_reg_write(host, GLAMO_REG_MMC_WDATADS2,
+ (uint16_t)(host->data_mem->start >> 16));
+
+ glamomci_reg_write(host, GLAMO_REG_MMC_RDATADS1,
+ (uint16_t)(host->data_mem->start));
+ glamomci_reg_write(host, GLAMO_REG_MMC_RDATADS2,
+ (uint16_t)(host->data_mem->start >> 16));
+
+}
+
+static int glamo_mci_clock_disable(struct mmc_host *mmc, int lazy)
+{
+ struct glamo_mci_host *host = mmc_priv(mmc);
+ glamo_engine_suspend(host->core, GLAMO_ENGINE_MMC);
+ return 0;
+}
+
+static int glamo_mci_clock_enable(struct mmc_host *mmc)
+{
+ struct glamo_mci_host *host = mmc_priv(mmc);
+ glamo_engine_enable(host->core, GLAMO_ENGINE_MMC);
+ return 0;
+}
+
+
+#ifndef GLAMO_MCI_WORKER
+static void do_pio_read(struct glamo_mci_host *host, struct mmc_data *data)
+{
+ struct sg_mapping_iter miter;
+ uint16_t __iomem *from_ptr = host->data_base;
+
+ dev_dbg(&host->pdev->dev, "pio_read():\n");
+
+ sg_miter_start(&miter, data->sg, data->sg_len, SG_MITER_TO_SG);
+
+ while (sg_miter_next(&miter)) {
+ memcpy(miter.addr, from_ptr, miter.length);
+ from_ptr += miter.length >> 1;
+
+ data->bytes_xfered += miter.length;
+ }
+
+ sg_miter_stop(&miter);
+
+ dev_dbg(&host->pdev->dev, "pio_read(): "
+ "complete (no more data).\n");
+}
+#endif
+
+static void do_pio_write(struct glamo_mci_host *host, struct mmc_data *data)
+{
+ struct sg_mapping_iter miter;
+ uint16_t __iomem *to_ptr = host->data_base;
+
+ dev_dbg(&host->pdev->dev, "pio_write():\n");
+ sg_miter_start(&miter, data->sg, data->sg_len, SG_MITER_FROM_SG);
+
+ while (sg_miter_next(&miter)) {
+ memcpy(to_ptr, miter.addr, miter.length);
+ to_ptr += miter.length >> 1;
+
+ data->bytes_xfered += miter.length;
+ }
+
+ sg_miter_stop(&miter);
+ dev_dbg(&host->pdev->dev, "pio_write(): complete\n");
+}
+
+static int glamo_mci_set_card_clock(struct glamo_mci_host *host, int freq)
+{
+ int real_rate = 0;
+
+ if (freq)
+ real_rate = glamo_engine_reclock(host->core, GLAMO_ENGINE_MMC,
+ freq);
+
+ return real_rate;
+}
+
+static int glamo_mci_wait_idle(struct glamo_mci_host *host,
+ unsigned long timeout)
+{
+ uint16_t status;
+ do {
+ status = glamomci_reg_read(host, GLAMO_REG_MMC_RB_STAT1);
+ } while (!(status & GLAMO_STAT1_MMC_IDLE) &&
+ time_is_after_jiffies(timeout));
+
+ if (time_is_before_eq_jiffies(timeout)) {
+ glamo_mci_reset(host);
+ return -ETIMEDOUT;
+ }
+
+ return 0;
+}
+
+static void glamo_mci_request_done(struct glamo_mci_host *host,
+ struct mmc_request *mrq)
+{
+ mmc_request_done(host->mmc, mrq);
+}
+
+static irqreturn_t glamo_mci_irq(int irq, void *data)
+{
+ struct glamo_mci_host *host = data;
+ struct mmc_request *mrq;
+ struct mmc_command *cmd;
+ uint16_t status;
+
+ if (!host->mrq || !host->mrq->cmd)
+ return IRQ_HANDLED;
+
+ mrq = host->mrq;
+ cmd = mrq->cmd;
+
+ status = glamomci_reg_read(host, GLAMO_REG_MMC_RB_STAT1);
+ dev_dbg(&host->pdev->dev, "status = 0x%04x\n", status);
+
+ /* we ignore a data timeout report if we are also told the data came */
+ if (status & GLAMO_STAT1_MMC_RB_DRDY)
+ status &= ~GLAMO_STAT1_MMC_DTOUT;
+
+ if (status & (GLAMO_STAT1_MMC_RTOUT | GLAMO_STAT1_MMC_DTOUT))
+ cmd->error = -ETIMEDOUT;
+ else if (status & (GLAMO_STAT1_MMC_BWERR | GLAMO_STAT1_MMC_BRERR))
+ cmd->error = -EILSEQ;
+
+ if (cmd->error) {
+ dev_info(&host->pdev->dev, "Error after cmd: 0x%x\n", status);
+ goto done;
+ }
+
+ /* issue STOP if we have been given one to use */
+ if (mrq->stop)
+ glamo_mci_send_command(host, mrq->stop);
+
+ if (cmd->data->flags & MMC_DATA_READ)
+#ifndef GLAMO_MCI_WORKER
+ do_pio_read(host, cmd->data);
+#else
+ flush_workqueue(host->workqueue);
+#endif
+
+ if (mrq->stop)
+ mrq->stop->error = glamo_mci_wait_idle(host, jiffies + HZ);
+
+done:
+ host->mrq = NULL;
+ glamo_mci_request_done(host, cmd->mrq);
+
+ return IRQ_HANDLED;
+}
+
+#ifdef GLAMO_MCI_WORKER
+static void glamo_mci_read_worker(struct work_struct *work)
+{
+ struct glamo_mci_host *host = container_of(work, struct glamo_mci_host,
+ read_work);
+ struct mmc_command *cmd;
+ uint16_t status;
+ uint16_t blocks_ready;
+ size_t data_read = 0;
+ size_t data_ready;
+ struct scatterlist *sg;
+ uint16_t __iomem *from_ptr = host->data_base;
+ void *sg_pointer;
+
+
+ cmd = host->mrq->cmd;
+ sg = cmd->data->sg;
+ do {
+ /*
+ * TODO: How to get rid of that?
+ * Maybe just drop it... In fact, it is already handled in
+ * the IRQ handler, maybe we should only check cmd->error.
+ * But the question is: what happens between the moment
+ * the error occurs, and the moment the IRQ handler handles it?
+ */
+ status = glamomci_reg_read(host, GLAMO_REG_MMC_RB_STAT1);
+
+ if (status & (GLAMO_STAT1_MMC_RTOUT | GLAMO_STAT1_MMC_DTOUT))
+ cmd->error = -ETIMEDOUT;
+ if (status & (GLAMO_STAT1_MMC_BWERR | GLAMO_STAT1_MMC_BRERR))
+ cmd->error = -EILSEQ;
+ if (cmd->error) {
+ dev_info(&host->pdev->dev, "Error after cmd: 0x%x\n",
+ status);
+ return;
+ }
+
+ blocks_ready = glamomci_reg_read(host, GLAMO_REG_MMC_RB_BLKCNT);
+ data_ready = blocks_ready * cmd->data->blksz;
+
+ if (data_ready == data_read)
+ yield();
+
+ while (sg && data_read + sg->length <= data_ready) {
+ sg_pointer = page_address(sg_page(sg)) + sg->offset;
+ memcpy(sg_pointer, from_ptr, sg->length);
+ from_ptr += sg->length >> 1;
+
+ data_read += sg->length;
+
+ sg = sg_next(sg);
+ }
+
+ } while (sg);
+ cmd->data->bytes_xfered = data_read;
+}
+#endif
+
+static void glamo_mci_send_command(struct glamo_mci_host *host,
+ struct mmc_command *cmd)
+{
+ uint8_t u8a[6];
+ uint16_t fire = 0;
+ unsigned int timeout = 1000000;
+ uint16_t *reg_resp = (uint16_t *)(host->mmio_base + GLAMO_REG_MMC_CMD_RSP1);
+ uint16_t status;
+ int triggers_int = 1;
+
+ /* if we can't do it, reject as busy */
+ if (!(glamomci_reg_read(host, GLAMO_REG_MMC_RB_STAT1) &
+ GLAMO_STAT1_MMC_IDLE)) {
+ cmd->error = -EBUSY;
+ return;
+ }
+
+ /* create an array in wire order for CRC computation */
+ u8a[0] = 0x40 | (cmd->opcode & 0x3f);
+ u8a[1] = (uint8_t)(cmd->arg >> 24);
+ u8a[2] = (uint8_t)(cmd->arg >> 16);
+ u8a[3] = (uint8_t)(cmd->arg >> 8);
+ u8a[4] = (uint8_t)cmd->arg;
+ u8a[5] = (crc7(0, u8a, 5) << 1) | 0x01;
+
+ /* issue the wire-order array including CRC in register order */
+ glamomci_reg_write(host, GLAMO_REG_MMC_CMD_REG1, ((u8a[4] << 8) | u8a[5]));
+ glamomci_reg_write(host, GLAMO_REG_MMC_CMD_REG2, ((u8a[2] << 8) | u8a[3]));
+ glamomci_reg_write(host, GLAMO_REG_MMC_CMD_REG3, ((u8a[0] << 8) | u8a[1]));
+
+ /* command index toggle */
+ fire |= (host->request_counter & 1) << 12;
+
+ /* set type of command */
+ switch (mmc_cmd_type(cmd)) {
+ case MMC_CMD_BC:
+ fire |= GLAMO_FIRE_MMC_CMDT_BNR;
+ break;
+ case MMC_CMD_BCR:
+ fire |= GLAMO_FIRE_MMC_CMDT_BR;
+ break;
+ case MMC_CMD_AC:
+ fire |= GLAMO_FIRE_MMC_CMDT_AND;
+ break;
+ case MMC_CMD_ADTC:
+ fire |= GLAMO_FIRE_MMC_CMDT_AD;
+ break;
+ }
+ /*
+ * if it expects a response, set the type expected
+ *
+ * R1, Length : 48bit, Normal response
+ * R1b, Length : 48bit, same R1, but added card busy status
+ * R2, Length : 136bit (really 128 bits with CRC snipped)
+ * R3, Length : 48bit (OCR register value)
+ * R4, Length : 48bit, SDIO_OP_CONDITION, Reverse SDIO Card
+ * R5, Length : 48bit, IO_RW_DIRECTION, Reverse SDIO Card
+ * R6, Length : 48bit (RCA register)
+ * R7, Length : 48bit (interface condition, VHS(voltage supplied),
+ * check pattern, CRC7)
+ */
+ switch (mmc_resp_type(cmd)) {
+ case MMC_RSP_R1: /* same index as R6 and R7 */
+ fire |= GLAMO_FIRE_MMC_RSPT_R1;
+ break;
+ case MMC_RSP_R1B:
+ fire |= GLAMO_FIRE_MMC_RSPT_R1b;
+ break;
+ case MMC_RSP_R2:
+ fire |= GLAMO_FIRE_MMC_RSPT_R2;
+ break;
+ case MMC_RSP_R3:
+ fire |= GLAMO_FIRE_MMC_RSPT_R3;
+ break;
+ /* R4 and R5 supported by chip not defined in linux/mmc/core.h (sdio) */
+ }
+ /*
+ * From the command index, set up the command class in the host ctrllr
+ *
+ * missing guys present on chip but couldn't figure out how to use yet:
+ * 0x0 "stream read"
+ * 0x9 "cancel running command"
+ */
+ switch (cmd->opcode) {
+ case MMC_READ_SINGLE_BLOCK:
+ fire |= GLAMO_FIRE_MMC_CC_SBR; /* single block read */
+ break;
+ case MMC_SWITCH: /* 64 byte payload */
+ case SD_APP_SEND_SCR:
+ case MMC_READ_MULTIPLE_BLOCK:
+ /* we will get an interrupt off this */
+ if (!cmd->mrq->stop) {
+ /* multiblock no stop */
+ fire |= GLAMO_FIRE_MMC_CC_MBRNS;
+ } else {
+ /* multiblock with stop */
+ fire |= GLAMO_FIRE_MMC_CC_MBRS;
+ }
+ break;
+ case MMC_WRITE_BLOCK:
+ fire |= GLAMO_FIRE_MMC_CC_SBW; /* single block write */
+ break;
+ case MMC_WRITE_MULTIPLE_BLOCK:
+ if (cmd->mrq->stop) {
+ /* multiblock with stop */
+ fire |= GLAMO_FIRE_MMC_CC_MBWS;
+ } else {
+ /* multiblock NO stop-- 'RESERVED'? */
+ fire |= GLAMO_FIRE_MMC_CC_MBWNS;
+ }
+ break;
+ case MMC_STOP_TRANSMISSION:
+ fire |= GLAMO_FIRE_MMC_CC_STOP; /* STOP */
+ triggers_int = 0;
+ break;
+ default:
+ fire |= GLAMO_FIRE_MMC_CC_BASIC; /* "basic command" */
+ triggers_int = 0;
+ break;
+ }
+
+ if (cmd->data)
+ host->mrq = cmd->mrq;
+
+ /* always largest timeout */
+ glamomci_reg_write(host, GLAMO_REG_MMC_TIMEOUT, 0xfff);
+
+ /* Generate interrupt on txfer */
+ glamomci_reg_set_bit_mask(host, GLAMO_REG_MMC_BASIC, 0xff36,
+ 0x0800 |
+ GLAMO_BASIC_MMC_NO_CLK_RD_WAIT |
+ GLAMO_BASIC_MMC_EN_COMPL_INT |
+ GLAMO_BASIC_MMC_EN_DATA_PUPS |
+ GLAMO_BASIC_MMC_EN_CMD_PUP);
+
+ /* send the command out on the wire */
+ /* dev_info(&host->pdev->dev, "Using FIRE %04X\n", fire); */
+ glamomci_reg_write(host, GLAMO_REG_MMC_CMD_FIRE, fire);
+
+ /* we are deselecting card? because it isn't going to ack then... */
+ if ((cmd->opcode == 7) && (cmd->arg == 0))
+ return;
+
+ /*
+ * we must spin until response is ready or timed out
+ * -- we don't get interrupts unless there is a bulk rx
+ */
+ do
+ status = glamomci_reg_read(host, GLAMO_REG_MMC_RB_STAT1);
+ while (((((status >> 15) & 1) != (host->request_counter & 1)) ||
+ (!(status & (GLAMO_STAT1_MMC_RB_RRDY |
+ GLAMO_STAT1_MMC_RTOUT |
+ GLAMO_STAT1_MMC_DTOUT |
+ GLAMO_STAT1_MMC_BWERR |
+ GLAMO_STAT1_MMC_BRERR)))) && (timeout--));
+
+ if ((status & (GLAMO_STAT1_MMC_RTOUT | GLAMO_STAT1_MMC_DTOUT)) ||
+ (timeout == 0)) {
+ cmd->error = -ETIMEDOUT;
+ } else if (status & (GLAMO_STAT1_MMC_BWERR | GLAMO_STAT1_MMC_BRERR)) {
+ cmd->error = -EILSEQ;
+ }
+
+ if (cmd->flags & MMC_RSP_PRESENT) {
+ if (cmd->flags & MMC_RSP_136) {
+ cmd->resp[3] = readw(&reg_resp[0]) |
+ (readw(&reg_resp[1]) << 16);
+ cmd->resp[2] = readw(&reg_resp[2]) |
+ (readw(&reg_resp[3]) << 16);
+ cmd->resp[1] = readw(&reg_resp[4]) |
+ (readw(&reg_resp[5]) << 16);
+ cmd->resp[0] = readw(&reg_resp[6]) |
+ (readw(&reg_resp[7]) << 16);
+ } else {
+ cmd->resp[0] = (readw(&reg_resp[0]) >> 8) |
+ (readw(&reg_resp[1]) << 8) |
+ (readw(&reg_resp[2]) << 24);
+ }
+ }
+
+#ifdef GLAMO_MCI_WORKER
+ /* We'll only get an interrupt when all data has been transfered.
+ By starting to copy data when it's avaiable we can increase
+ throughput by up to 30%. */
+ if (cmd->data && (cmd->data->flags & MMC_DATA_READ))
+ queue_work(host->workqueue, &host->read_work);
+#endif
+
+}
+
+static int glamo_mci_prepare_pio(struct glamo_mci_host *host,
+ struct mmc_data *data)
+{
+ /* set up the block info */
+ glamomci_reg_write(host, GLAMO_REG_MMC_DATBLKLEN, data->blksz);
+ glamomci_reg_write(host, GLAMO_REG_MMC_DATBLKCNT, data->blocks);
+
+ data->bytes_xfered = 0;
+
+ /* if write, prep the write into the shared RAM before the command */
+ if (data->flags & MMC_DATA_WRITE)
+ do_pio_write(host, data);
+
+ dev_dbg(&host->pdev->dev, "(blksz=%d, count=%d)\n",
+ data->blksz, data->blocks);
+ return 0;
+}
+
+static void glamo_mci_send_request(struct mmc_host *mmc,
+ struct mmc_request *mrq)
+{
+ struct glamo_mci_host *host = mmc_priv(mmc);
+ struct mmc_command *cmd = mrq->cmd;
+
+ host->request_counter++;
+ if (cmd->data) {
+ if (glamo_mci_prepare_pio(host, cmd->data)) {
+ cmd->error = -EIO;
+ cmd->data->error = -EIO;
+ goto done;
+ }
+ }
+
+ dev_dbg(&host->pdev->dev, "cmd 0x%x, "
+ "arg 0x%x data=%p mrq->stop=%p flags 0x%x\n",
+ cmd->opcode, cmd->arg, cmd->data, cmd->mrq->stop,
+ cmd->flags);
+
+ glamo_mci_send_command(host, cmd);
+
+ /*
+ * if we don't have bulk data to take care of, we're done
+ */
+ if (!cmd->data || cmd->error)
+ goto done;
+
+ /*
+ * Otherwise can can use the interrupt as async completion --
+ * if there is read data coming, or we wait for write data to complete,
+ * exit without mmc_request_done() as the payload interrupt
+ * will service it
+ */
+ dev_dbg(&host->pdev->dev, "Waiting for payload data\n");
+ return;
+done:
+ if (!cmd->error)
+ cmd->error = glamo_mci_wait_idle(host, jiffies + 2 * HZ);
+ glamo_mci_request_done(host, mrq);
+}
+
+static void glamo_mci_set_power_mode(struct glamo_mci_host *host,
+ unsigned char power_mode)
+{
+ int ret;
+
+ if (power_mode == host->power_mode)
+ return;
+
+ switch (power_mode) {
+ case MMC_POWER_UP:
+ if (host->power_mode == MMC_POWER_OFF) {
+ ret = regulator_enable(host->regulator);
+ if (ret)
+ dev_err(&host->pdev->dev,
+ "Failed to enable regulator: %d\n",
+ ret);
+ }
+ break;
+ case MMC_POWER_ON:
+ break;
+ case MMC_POWER_OFF:
+ default:
+ ret = regulator_disable(host->regulator);
+ if (ret)
+ dev_warn(&host->pdev->dev,
+ "Failed to disable regulator: %d\n",
+ ret);
+ break;
+ }
+ host->power_mode = power_mode;
+}
+
+static void glamo_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
+{
+ struct glamo_mci_host *host = mmc_priv(mmc);
+ int bus_width = 0;
+ int rate;
+ int sd_drive;
+ int ret;
+
+ mmc_host_enable(mmc);
+
+ /* Set power */
+ glamo_mci_set_power_mode(host, ios->power_mode);
+
+ if (host->vdd != ios->vdd) {
+ ret = mmc_regulator_set_ocr(host->regulator, ios->vdd);
+ if (ret)
+ dev_err(&host->pdev->dev,
+ "Failed to set regulator voltage: %d\n", ret);
+ else
+ host->vdd = ios->vdd;
+ }
+
+ rate = glamo_mci_set_card_clock(host, ios->clock);
+
+ if ((ios->power_mode == MMC_POWER_ON) ||
+ (ios->power_mode == MMC_POWER_UP)) {
+ dev_info(&host->pdev->dev,
+ "powered (vdd = %hu) clk: %dkHz div=%hu (req: %ukHz). "
+ "Bus width=%d\n", ios->vdd,
+ rate / 1000, 0,
+ ios->clock / 1000, (int)ios->bus_width);
+ } else {
+ dev_info(&host->pdev->dev, "glamo_mci_set_ios: power down.\n");
+ }
+
+ /* set bus width */
+ if (ios->bus_width == MMC_BUS_WIDTH_4)
+ bus_width = GLAMO_BASIC_MMC_EN_4BIT_DATA;
+
+ sd_drive = (rate * 4) / host->clk_rate;
+ if (sd_drive > 3)
+ sd_drive = 3;
+
+ glamomci_reg_set_bit_mask(host, GLAMO_REG_MMC_BASIC,
+ GLAMO_BASIC_MMC_EN_4BIT_DATA | 0xc0,
+ bus_width | sd_drive << 6);
+
+ if (host->power_mode == MMC_POWER_OFF)
+ mmc_host_disable(host->mmc);
+ else
+ mmc_host_lazy_disable(host->mmc);
+}
+
+
+/*
+ * no physical write protect supported by us
+ */
+static int glamo_mci_get_ro(struct mmc_host *mmc)
+{
+ return 0;
+}
+
+static struct mmc_host_ops glamo_mci_ops = {
+ .enable = glamo_mci_clock_enable,
+ .disable = glamo_mci_clock_disable,
+ .request = glamo_mci_send_request,
+ .set_ios = glamo_mci_set_ios,
+ .get_ro = glamo_mci_get_ro,
+};
+
+static int glamo_mci_probe(struct platform_device *pdev)
+{
+ struct mmc_host *mmc;
+ struct glamo_mci_host *host;
+ struct glamo_core *core = dev_get_drvdata(pdev->dev.parent);
+ int ret;
+
+ dev_info(&pdev->dev, "glamo_mci driver (C)2007 Openmoko, Inc\n");
+
+ mmc = mmc_alloc_host(sizeof(struct glamo_mci_host), &pdev->dev);
+ if (!mmc) {
+ ret = -ENOMEM;
+ goto probe_out;
+ }
+
+ host = mmc_priv(mmc);
+ host->mmc = mmc;
+ host->pdev = pdev;
+ if (core->pdata)
+ host->pdata = core->pdata->mmc_data;
+ host->power_mode = MMC_POWER_OFF;
+ host->core = core;
+ host->irq = platform_get_irq(pdev, 0);
+
+#ifdef GLAMO_MCI_WORKER
+ INIT_WORK(&host->read_work, glamo_mci_read_worker);
+ host->workqueue = create_singlethread_workqueue("glamo-mci-read");
+#endif
+
+ host->regulator = regulator_get(pdev->dev.parent, "SD_3V3");
+ if (IS_ERR(host->regulator)) {
+ dev_err(&pdev->dev, "Cannot proceed without regulator.\n");
+ ret = PTR_ERR(host->regulator);
+ goto probe_free_host;
+ }
+
+ host->mmio_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!host->mmio_mem) {
+ dev_err(&pdev->dev,
+ "failed to get io memory region resouce.\n");
+ ret = -ENOENT;
+ goto probe_regulator_put;
+ }
+
+ host->mmio_mem = request_mem_region(host->mmio_mem->start,
+ resource_size(host->mmio_mem),
+ pdev->name);
+
+ if (!host->mmio_mem) {
+ dev_err(&pdev->dev, "failed to request io memory region.\n");
+ ret = -ENOENT;
+ goto probe_regulator_put;
+ }
+
+ host->mmio_base = ioremap(host->mmio_mem->start,
+ resource_size(host->mmio_mem));
+ if (!host->mmio_base) {
+ dev_err(&pdev->dev, "failed to ioremap() io memory region.\n");
+ ret = -EINVAL;
+ goto probe_free_mem_region_mmio;
+ }
+
+
+ /* Get ahold of our data buffer we use for data in and out on MMC */
+ host->data_mem = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ if (!host->data_mem) {
+ dev_err(&pdev->dev,
+ "failed to get io memory region resource.\n");
+ ret = -ENOENT;
+ goto probe_iounmap_mmio;
+ }
+
+ host->data_mem = request_mem_region(host->data_mem->start,
+ resource_size(host->data_mem),
+ pdev->name);
+
+ if (!host->data_mem) {
+ dev_err(&pdev->dev, "failed to request io memory region.\n");
+ ret = -ENOENT;
+ goto probe_iounmap_mmio;
+ }
+ host->data_base = ioremap(host->data_mem->start,
+ resource_size(host->data_mem));
+
+ if (host->data_base == 0) {
+ dev_err(&pdev->dev, "failed to ioremap() io memory region.\n");
+ ret = -EINVAL;
+ goto probe_free_mem_region_data;
+ }
+
+ ret = request_threaded_irq(host->irq, NULL, glamo_mci_irq, IRQF_SHARED,
+ pdev->name, host);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to register irq.\n");
+ goto probe_iounmap_data;
+ }
+
+
+ host->vdd = 0;
+ host->clk_rate = glamo_pll_rate(host->core, GLAMO_PLL1);
+
+ /* explain our host controller capabilities */
+ mmc->ops = &glamo_mci_ops;
+ mmc->ocr_avail = mmc_regulator_get_ocrmask(host->regulator);
+ mmc->caps = MMC_CAP_4_BIT_DATA |
+ MMC_CAP_MMC_HIGHSPEED |
+ MMC_CAP_SD_HIGHSPEED;
+
+ if (host->pdata->nonremovable)
+ mmc->caps |= MMC_CAP_NONREMOVABLE;
+
+ mmc->f_min = host->clk_rate / 256;
+ mmc->f_max = sd_max_clk;
+
+ mmc->max_blk_count = (1 << 16) - 1; /* GLAMO_REG_MMC_RB_BLKCNT */
+ mmc->max_blk_size = (1 << 12) - 1; /* GLAMO_REG_MMC_RB_BLKLEN */
+ mmc->max_req_size = resource_size(host->data_mem);
+ mmc->max_seg_size = mmc->max_req_size;
+ mmc->max_phys_segs = 128;
+ mmc->max_hw_segs = 128;
+
+ if (mmc->ocr_avail < 0) {
+ dev_warn(&pdev->dev,
+ "Failed to get ocr list for regulator: %d.\n",
+ mmc->ocr_avail);
+ mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
+ }
+
+ platform_set_drvdata(pdev, mmc);
+
+ mmc->caps |= MMC_CAP_DISABLE;
+ mmc_set_disable_delay(mmc, 1000 / 16);
+
+ mmc_host_enable(mmc);
+ glamo_mci_reset(host);
+
+ ret = mmc_add_host(mmc);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to add mmc host.\n");
+ goto probe_mmc_host_disable;
+ }
+
+ mmc_host_lazy_disable(mmc);
+
+ return 0;
+
+probe_mmc_host_disable:
+ mmc_host_disable(mmc);
+ free_irq(host->irq, host);
+probe_iounmap_data:
+ iounmap(host->data_base);
+probe_free_mem_region_data:
+ release_mem_region(host->data_mem->start,
+ resource_size(host->data_mem));
+probe_iounmap_mmio:
+ iounmap(host->mmio_base);
+probe_free_mem_region_mmio:
+ release_mem_region(host->mmio_mem->start,
+ resource_size(host->mmio_mem));
+probe_regulator_put:
+ regulator_put(host->regulator);
+probe_free_host:
+#ifdef GLAMO_MCI_WORKER
+ destroy_workqueue(host->workqueue);
+#endif
+ mmc_free_host(mmc);
+probe_out:
+ return ret;
+}
+
+static int glamo_mci_remove(struct platform_device *pdev)
+{
+ struct mmc_host *mmc = platform_get_drvdata(pdev);
+ struct glamo_mci_host *host = mmc_priv(mmc);
+
+#ifdef GLAMO_MCI_WORKER
+ flush_workqueue(host->workqueue);
+ destroy_workqueue(host->workqueue);
+#endif
+
+ mmc_host_enable(mmc);
+ mmc_remove_host(mmc);
+ mmc_host_disable(mmc);
+
+ synchronize_irq(host->irq);
+ free_irq(host->irq, host);
+
+ iounmap(host->mmio_base);
+ iounmap(host->data_base);
+ release_mem_region(host->mmio_mem->start,
+ resource_size(host->mmio_mem));
+ release_mem_region(host->data_mem->start,
+ resource_size(host->data_mem));
+
+ regulator_put(host->regulator);
+
+ mmc_free_host(mmc);
+
+ return 0;
+}
+
+
+#ifdef CONFIG_PM
+
+static int glamo_mci_suspend(struct device *dev)
+{
+ struct mmc_host *mmc = dev_get_drvdata(dev);
+ struct glamo_mci_host *host = mmc_priv(mmc);
+ int ret;
+
+ disable_irq(host->irq);
+
+ mmc_host_enable(mmc);
+ ret = mmc_suspend_host(mmc, PMSG_SUSPEND);
+ mmc_host_disable(mmc);
+
+ return ret;
+}
+
+static int glamo_mci_resume(struct device *dev)
+{
+ struct mmc_host *mmc = dev_get_drvdata(dev);
+ struct glamo_mci_host *host = mmc_priv(mmc);
+ int ret;
+
+ mmc_host_enable(mmc);
+ glamo_mci_reset(host);
+ mdelay(10);
+
+ enable_irq(host->irq);
+
+ ret = mmc_resume_host(host->mmc);
+
+ mmc_host_lazy_disable(host->mmc);
+
+ return ret;
+}
+
+static const struct dev_pm_ops glamo_mci_pm_ops = {
+ .suspend = glamo_mci_suspend,
+ .resume = glamo_mci_resume,
+ .freeze = glamo_mci_suspend,
+ .thaw = glamo_mci_resume,
+};
+#define GLAMO_MCI_PM_OPS (&glamo_mci_pm_ops)
+
+#else /* CONFIG_PM */
+#define GLAMO_MCI_PM_OPS NULL
+#endif /* CONFIG_PM */
+
+
+static struct platform_driver glamo_mci_driver = {
+ .probe = glamo_mci_probe,
+ .remove = glamo_mci_remove,
+ .driver = {
+ .name = "glamo-mci",
+ .owner = THIS_MODULE,
+ .pm = GLAMO_MCI_PM_OPS,
+ },
+};
+
+static int __init glamo_mci_init(void)
+{
+ platform_driver_register(&glamo_mci_driver);
+ return 0;
+}
+module_init(glamo_mci_init);
+
+static void __exit glamo_mci_exit(void)
+{
+ platform_driver_unregister(&glamo_mci_driver);
+}
+module_exit(glamo_mci_exit);
+
+MODULE_DESCRIPTION("Glamo MMC/SD Card Interface driver");
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Andy Green <andy(a)openmoko.com>");
+MODULE_ALIAS("platform:glamo-mci");
--
1.7.1

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo(a)vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/