Prev: [PATCH 4/6] mfd/stmpexxx: change touchscreen irq
Next: [PATCH 1/6] gpio/stmpe-gpio: set GPIO alternate function while requesting
From: Luotao Fu on 24 Jun 2010 07:20
Signed-off-by: Luotao Fu <l.fu(a)pengutronix.de>
---
include/linux/mfd/stmpe.h | 43 +++++++++++++++++++++++++++++++++++++++++++
1 files changed, 43 insertions(+), 0 deletions(-)

diff --git a/include/linux/mfd/stmpe.h b/include/linux/mfd/stmpe.h
index cf2155f..3d319a1 100644
--- a/include/linux/mfd/stmpe.h
+++ b/include/linux/mfd/stmpe.h
@@ -124,6 +124,47 @@ struct stmpe_gpio_platform_data {
};

/**
+ * struct stmpe_ts_platform_data - stmpe811 touch screen controller platform
+ * data
+ * @sample_time: ADC converstion time in number of clock.
+ * (0 -> 36 clocks, 1 -> 44 clocks, 2 -> 56 clocks, 3 -> 64 clocks,
+ * 4 -> 80 clocks, 5 -> 96 clocks, 6 -> 144 clocks),
+ * recommended is 4.
+ * @mod_12b: ADC Bit mode (0 -> 10bit ADC, 1 -> 12bit ADC)
+ * @ref_sel: ADC reference source
+ * (0 -> internal reference, 1 -> external reference)
+ * @adc_freq: ADC Clock speed
+ * (0 -> 1.625 MHz, 1 -> 3.25 MHz, 2 || 3 -> 6.5 MHz)
+ * @ave_ctrl: Sample average control
+ * (0 -> 1 sample, 1 -> 2 samples, 2 -> 4 samples, 3 -> 8 samples)
+ * @touch_det_delay: Touch detect interrupt delay
+ * (0 -> 10 us, 1 -> 50 us, 2 -> 100 us, 3 -> 500 us,
+ * 4-> 1 ms, 5 -> 5 ms, 6 -> 10 ms, 7 -> 50 ms)
+ * recommended is 3
+ * @settling: Panel driver settling time
+ * (0 -> 10 us, 1 -> 100 us, 2 -> 500 us, 3 -> 1 ms,
+ * 4 -> 5 ms, 5 -> 10 ms, 6 for 50 ms, 7 -> 100 ms)
+ * recommended is 2
+ * @fraction_z: Length of the fractional part in z
+ * (fraction_z ([0..7]) = Count of the fractional part)
+ * recommended is 7
+ * @i_drive: current limit value of the touchscreen drivers
+ * (0 -> 20 mA typical 35 mA max, 1 -> 50 mA typical 80 mA max)
+ *
+ * */
+struct stmpe_ts_platform_data {
+ u8 sample_time;
+ u8 mod_12b;
+ u8 ref_sel;
+ u8 adc_freq;
+ u8 ave_ctrl;
+ u8 touch_det_delay;
+ u8 settling;
+ u8 fraction_z;
+ u8 i_drive;
+};
+
+/**
* struct stmpe_platform_data - STMPE platform data
* @id: device id to distinguish between multiple STMPEs on the same board
* @blocks: bitmask of blocks to enable (use STMPE_BLOCK_*)
@@ -133,6 +174,7 @@ struct stmpe_gpio_platform_data {
* %STMPE_NR_INTERNAL_IRQS if the GPIO driver is not used.
* @gpio: GPIO-specific platform data
* @keypad: keypad-specific platform data
+ * @ts: touchscreen-specific platform data
*/
struct stmpe_platform_data {
int id;
@@ -143,6 +185,7 @@ struct stmpe_platform_data {

struct stmpe_gpio_platform_data *gpio;
struct stmpe_keypad_platform_data *keypad;
+ struct stmpe_ts_platform_data *ts;
};

#define STMPE_NR_INTERNAL_IRQS 9
--
1.7.1

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo(a)vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
 | 
Pages: 1
Prev: [PATCH 4/6] mfd/stmpexxx: change touchscreen irq
Next: [PATCH 1/6] gpio/stmpe-gpio: set GPIO alternate function while requesting