From: Guenter Roeck on
This patch adds support for W83667HG-B to the w83627ehf driver.

Signed-off-by: Guenter Roeck <guenter.roeck(a)ericsson.com>
---

Key relevant difference between W83667HG and W83667HG-B are the Chip ID as well
as the fan output and step output register addresses. Those differences are
addressed with this patch.

There are other relevant changes in the mapping of input sensors to fan
control (W83667HG datasheet chapter 8.7, W83667HG-B datasheet chapter 8.5).
However, control of those mappings is not implemented in the driver, thus the
respective changes should not have an impact on driver operation.

Changes made in this patch are based on information from datasheets only. The
patch has not yet been tested with real hardware. The patch must be tested with
real hardware before it is integrated, and is thus submitted as RFC.

---
drivers/hwmon/w83627ehf.c | 44 +++++++++++++++++++++++++++++++++++++-------
1 files changed, 37 insertions(+), 7 deletions(-)

diff --git a/drivers/hwmon/w83627ehf.c b/drivers/hwmon/w83627ehf.c
index 0dcaba9..074e15b 100644
--- a/drivers/hwmon/w83627ehf.c
+++ b/drivers/hwmon/w83627ehf.c
@@ -39,6 +39,7 @@
w83627dhg 9 5 4 3 0xa020 0xc1 0x5ca3
w83627dhg-p 9 5 4 3 0xb070 0xc1 0x5ca3
w83667hg 9 5 3 3 0xa510 0xc1 0x5ca3
+ w83667hg-b 9 5 3 3 0xb350 0xc1 0x5ca3
*/

#include <linux/module.h>
@@ -55,7 +56,7 @@
#include <linux/io.h>
#include "lm75.h"

-enum kinds { w83627ehf, w83627dhg, w83627dhg_p, w83667hg };
+enum kinds { w83627ehf, w83627dhg, w83627dhg_p, w83667hg, w83667hg_b };

/* used to set data->name = w83627ehf_device_names[data->sio_kind] */
static const char * w83627ehf_device_names[] = {
@@ -63,6 +64,7 @@ static const char * w83627ehf_device_names[] = {
"w83627dhg",
"w83627dhg",
"w83667hg",
+ "w83667hg-b",
};

static unsigned short force_id;
@@ -91,6 +93,7 @@ MODULE_PARM_DESC(force_id, "Override the detected device ID");
#define SIO_W83627DHG_ID 0xa020
#define SIO_W83627DHG_P_ID 0xb070
#define SIO_W83667HG_ID 0xa510
+#define SIO_W83667HG_B_ID 0xb350
#define SIO_ID_MASK 0xFFF0

static inline void
@@ -201,8 +204,17 @@ static const u8 W83627EHF_REG_TOLERANCE[] = { 0x07, 0x07, 0x14, 0x62 };
static const u8 W83627EHF_REG_FAN_START_OUTPUT[] = { 0x0a, 0x0b, 0x16, 0x65 };
static const u8 W83627EHF_REG_FAN_STOP_OUTPUT[] = { 0x08, 0x09, 0x15, 0x64 };
static const u8 W83627EHF_REG_FAN_STOP_TIME[] = { 0x0c, 0x0d, 0x17, 0x66 };
-static const u8 W83627EHF_REG_FAN_MAX_OUTPUT[] = { 0xff, 0x67, 0xff, 0x69 };
-static const u8 W83627EHF_REG_FAN_STEP_OUTPUT[] = { 0xff, 0x68, 0xff, 0x6a };
+
+static const u8 *W83627EHF_REG_FAN_MAX_OUTPUT;
+static const u8 *W83627EHF_REG_FAN_STEP_OUTPUT;
+
+static const u8 W83627EHF_REG_FAN_MAX_OUTPUT_COMMON[]
+ = { 0xff, 0x67, 0xff, 0x69 };
+static const u8 W83627EHF_REG_FAN_STEP_OUTPUT_COMMON[]
+ = { 0xff, 0x68, 0xff, 0x6a };
+
+static const u8 W83627EHF_REG_FAN_MAX_OUTPUT_W83667_B[] = { 0x67, 0x69, 0x6b };
+static const u8 W83627EHF_REG_FAN_STEP_OUTPUT_W83667_B[] = { 0x68, 0x6a, 0x6c };

/*
* Conversions
@@ -1343,22 +1355,35 @@ static int __devinit w83627ehf_probe(struct platform_device *pdev)
/* 627EHG and 627EHF have 10 voltage inputs; 627DHG and 667HG have 9 */
data->in_num = (sio_data->kind == w83627ehf) ? 10 : 9;
/* 667HG has 3 pwms */
- data->pwm_num = (sio_data->kind == w83667hg) ? 3 : 4;
+ data->pwm_num = (sio_data->kind == w83667hg
+ || sio_data->kind == w83667hg_b) ? 3 : 4;

/* Check temp3 configuration bit for 667HG */
- if (sio_data->kind == w83667hg) {
+ if (sio_data->kind == w83667hg || sio_data->kind == w83667hg_b) {
data->temp3_disable = w83627ehf_read_value(data,
W83627EHF_REG_TEMP_CONFIG[1]) & 0x01;
data->in6_skip = !data->temp3_disable;
}

+ if (sio_data->kind == w83667hg_b) {
+ W83627EHF_REG_FAN_MAX_OUTPUT
+ = W83627EHF_REG_FAN_MAX_OUTPUT_W83667_B;
+ W83627EHF_REG_FAN_STEP_OUTPUT
+ = W83627EHF_REG_FAN_STEP_OUTPUT_W83667_B;
+ } else {
+ W83627EHF_REG_FAN_MAX_OUTPUT
+ = W83627EHF_REG_FAN_MAX_OUTPUT_COMMON;
+ W83627EHF_REG_FAN_STEP_OUTPUT
+ = W83627EHF_REG_FAN_STEP_OUTPUT_COMMON;
+ }
+
/* Initialize the chip */
w83627ehf_init_device(data);

data->vrm = vid_which_vrm();
superio_enter(sio_data->sioreg);
/* Read VID value */
- if (sio_data->kind == w83667hg) {
+ if (sio_data->kind == w83667hg || sio_data->kind == w83667hg_b) {
/* W83667HG has different pins for VID input and output, so
we can get the VID input values directly at logical device D
0xe3. */
@@ -1409,7 +1434,7 @@ static int __devinit w83627ehf_probe(struct platform_device *pdev)
}

/* fan4 and fan5 share some pins with the GPIO and serial flash */
- if (sio_data->kind == w83667hg) {
+ if (sio_data->kind == w83667hg || sio_data->kind == w83667hg_b) {
fan5pin = superio_inb(sio_data->sioreg, 0x27) & 0x20;
fan4pin = superio_inb(sio_data->sioreg, 0x27) & 0x40;
} else {
@@ -1556,6 +1581,7 @@ static int __init w83627ehf_find(int sioaddr, unsigned short *addr,
static const char __initdata sio_name_W83627DHG[] = "W83627DHG";
static const char __initdata sio_name_W83627DHG_P[] = "W83627DHG-P";
static const char __initdata sio_name_W83667HG[] = "W83667HG";
+ static const char __initdata sio_name_W83667HG_B[] = "W83667HG-B";

u16 val;
const char *sio_name;
@@ -1588,6 +1614,10 @@ static int __init w83627ehf_find(int sioaddr, unsigned short *addr,
sio_data->kind = w83667hg;
sio_name = sio_name_W83667HG;
break;
+ case SIO_W83667HG_B_ID:
+ sio_data->kind = w83667hg_b;
+ sio_name = sio_name_W83667HG_B;
+ break;
default:
if (val != 0xffff)
pr_debug(DRVNAME ": unsupported chip ID: 0x%04x\n",
--
1.7.0.87.g0901d

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo(a)vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/