Prev: ISE7.1 PAR Warinng: excessive skew because 1 NON-CLK pins...
Next: errors during MAP
From: damidar on 14 Jun 2005 12:16
hi....Please help me for a programmer xilinx XC9536XL (parallel LPT)

When i starter to program, it stopped on:

"Error:IMPACT 583 :the idcode read from the device does not match the
idcode in the bsdl"

:(

Help me thanks a lot.....

From: Vladislav Muravin on 14 Jun 2005 12:23
If this is your first time with the board & there are many '1's with IDcode,
try thinking about signal integrity issue or board problems...

Vladislav

"damidar" <dejavu99(a)hotmail-dot-it.no-spam.invalid> wrote in message
news:MfidnZJr6fJ5nzLfRVn_vg(a)giganews.com...
> hi....Please help me for a programmer xilinx XC9536XL (parallel LPT)
>
> When i starter to program, it stopped on:
>
> "Error:IMPACT 583 :the idcode read from the device does not match the
> idcode in the bsdl"
>
> :(
>
> Help me thanks a lot.....
>


From: David Brown on 14 Jun 2005 13:14
Depending on which software you are using there was an error in 5.3i related
to Error code 583. I would try going to the Xilinx website and searching for
"IMPACT 583".

dbrown

"Vladislav Muravin" <muravinv(a)advantech.ca> wrote in message
news:WvDre.6378$yU.335951(a)news20.bellglobal.com...
> If this is your first time with the board & there are many '1's with
> IDcode,
> try thinking about signal integrity issue or board problems...
>
> Vladislav
>
> "damidar" <dejavu99(a)hotmail-dot-it.no-spam.invalid> wrote in message
> news:MfidnZJr6fJ5nzLfRVn_vg(a)giganews.com...
>> hi....Please help me for a programmer xilinx XC9536XL (parallel LPT)
>>
>> When i starter to program, it stopped on:
>>
>> "Error:IMPACT 583 :the idcode read from the device does not match the
>> idcode in the bsdl"
>>
>> :(
>>
>> Help me thanks a lot.....
>>
>
>


From: Bruno on 14 Jun 2005 18:51
Hello,

I think I already had a similar problem with a XC9536! The ID Code was
wrong! I was using a long LPT cable! I suspected a Signal Integrity problem
and put a capacitor to slow down the edges! The ID code was read
successfully and the device was also programmed successfully. To do a quick
test, use an oscilloscope probe to load the lines. I don't remember in what
line was. Try all four.


Hope this helps
Bruno


"damidar" <dejavu99(a)hotmail-dot-it.no-spam.invalid> escreveu na mensagem
news:MfidnZJr6fJ5nzLfRVn_vg(a)giganews.com...
> hi....Please help me for a programmer xilinx XC9536XL (parallel LPT)
>
> When i starter to program, it stopped on:
>
> "Error:IMPACT 583 :the idcode read from the device does not match the
> idcode in the bsdl"
>
> :(
>
> Help me thanks a lot.....
>


From: Evan Samuel on 15 Jun 2005 01:31
Two possible causes.

1. You are not using the latest version of the Impact tool. When Xilinx
updates the FAB process to various chips, it will sometimes render older
versions of Impact incompatiable. If you haven't purchased the latest
version of ISE, try the Webpack version of Impact from their website.

2. The parallel 3 cable is prone to noise. Check all your connections an
try moving the cable away from any noise sources.



dejavu99(a)hotmail-dot-it.no-spam.invalid (damidar) wrote in
news:MfidnZJr6fJ5nzLfRVn_vg(a)giganews.com:

> hi....Please help me for a programmer xilinx XC9536XL (parallel LPT)
>
> When i starter to program, it stopped on:
>
> "Error:IMPACT 583 :the idcode read from the device does not match the
> idcode in the bsdl"
>
> :(
>
> Help me thanks a lot.....
>

 |  Next  |  Last
Pages: 1 2 3
Prev: ISE7.1 PAR Warinng: excessive skew because 1 NON-CLK pins...
Next: errors during MAP