Prev: Resetting logins and password
Next: Wi-Fi deployment in computer conference
From: samadams_2006 on 21 Apr 2008 00:10
Hello,

A few years ago, when I initially installed my linksys router, I set
it up so that only the network had a password, but so that only my
current laptop could access it (I believe via the computer name). I
have a new laptop and I would like to add this computer to the
criteria, but I do not remember how to do this via the linksys
software. Does anyone know how to do this?

Thanks
From: Jeff Liebermann on 21 Apr 2008 11:44
On Sun, 20 Apr 2008 21:10:22 -0700 (PDT), samadams_2006(a)yahoo.ca
wrote:

>A few years ago, when I initially installed my linksys router, I set
>it up so that only the network had a password, but so that only my
>current laptop could access it (I believe via the computer name). I
>have a new laptop and I would like to add this computer to the
>criteria, but I do not remember how to do this via the linksys
>software. Does anyone know how to do this?

Any particular Linksys model router? The hardware version (from the
serial number tag) and the firmware version (from the setup page)
would also be nice.

If the restrictions were only for the wireless network, you have a
WEP, WPA, or WPA2 encryption key setup on the "wireless security"
page. Use a wired ethernet connection to do the setup if you lost it.

--
Jeff Liebermann jeffl(a)cruzio.com
150 Felker St #D http://www.LearnByDestroying.com
Santa Cruz CA 95060 http://802.11junk.com
Skype: JeffLiebermann AE6KS 831-336-2558
From: ps56k on 21 Apr 2008 12:03
samadams_2006(a)yahoo.ca wrote:
> Hello,
>
> A few years ago, when I initially installed my linksys router, I set
> it up so that only the network had a password, but so that only my
> current laptop could access it (I believe via the computer name). I
> have a new laptop and I would like to add this computer to the
> criteria, but I do not remember how to do this via the linksys
> software. Does anyone know how to do this?
>
> Thanks

I have no idea what this all means...
> I set it up so that only the network had a password,
> but so that only my current laptop could access it
> (I believe via the computer name).

A - for the wireless side, you could have setup encryption key - WEP, WPA,
etc
B - for the wireless side, you could have used a MAC address access list

C - Some Linksys devices have a "permission list" that lists computer IP
addresses or MACs,
and the times of day they can access the router network - ala parental
controls -

So - which Linksys router do you have,
and which set of controls do you think you used ?


From: samadams_2006 on 21 Apr 2008 18:26
Hello Again,

I have Linksys Model RTP300.

Thanks
Sam
From: Jeff Liebermann on 21 Apr 2008 18:41
On Mon, 21 Apr 2008 15:26:33 -0700 (PDT), samadams_2006(a)yahoo.ca
wrote:

>Hello Again,
>I have Linksys Model RTP300.

That's not a wireless router:
<http://www.linksys.com/servlet/Satellite?c=L_Product_C2&childpagename=US%2FLayout&cid=1119460383933&pagename=Linksys%2FCommon%2FVisitorWrapper>
Without wireless encryption, your question makes little sense.
Sorry, but I can't decode what you're trying to accomplish. Try
again, this time supplying a better description of what you are trying
to accomplish. Also, the RTP300 is normally distributed by various
service providers. You might call support at your VoIP provider for
help.

--
Jeff Liebermann jeffl(a)cruzio.com
150 Felker St #D http://www.LearnByDestroying.com
Santa Cruz CA 95060 http://802.11junk.com
Skype: JeffLiebermann AE6KS 831-336-2558
 | 
Pages: 1
Prev: Resetting logins and password
Next: Wi-Fi deployment in computer conference