Prev: Epson EPL-3000 printer... how to...
Next: MP530 using a lot of cyan and red
From: Tom D. on 10 May 2010 12:36
I have an HP 940c which has been great until now. Recently had it in storage for almost 2 months. When I started it up again the graphics are now printing misaligned. Went through the alignment procedure, but row "B" on the alignment sheet never comes close to being aligned.
I take this to mean that it is so far out that software alone won't solve it. I changed the cartridges as a precaution, but no luck.
Any idea how this happened or how to fix it - could find no information anywhere.


--------------= Posted using GrabIt =----------------
------= Binary Usenet downloading made easy =---------
-= Get GrabIt for free from http://www.shemes.com/ =-

From: Fred McKenzie on 14 May 2010 01:02
In article <4be83610$0$31284$607ed4bc(a)cv.net>,
"Tom D." <delo724(a)yahoo.com> wrote:

> I have an HP 940c which has been great until now. Recently had it in storage
> for almost 2 months. When I started it up again the graphics are now printing
> misaligned. Went through the alignment procedure, but row "B" on the
> alignment sheet never comes close to being aligned.
> I take this to mean that it is so far out that software alone won't solve it.
> I changed the cartridges as a precaution, but no luck.
> Any idea how this happened or how to fix it - could find no information
> anywhere.

Tom-

I'm not familiar with the 940c. Many printers have an ink head that
travels back and forth on a metal bar. It prints a line of characters
left to right, and then prints a reversed line when traveling right to
left.

If there was any kind of oil on the metal bar, it could collect paper
dust. Some oil might also oxidize with the same result of slowing down
the print head as it travels across, so characters printed one way might
not line up with those printed during the return trip.

If this happens to be the case, the solution may be to clean the bar.
There may be a proper kind of lubricant to use, but it might also be
designed so plastic riding on polished metal doesn't need any.

Fred
From: John on 16 May 2010 10:26
On Fri, 14 May 2010 01:02:18 -0400, Fred McKenzie <fmmck(a)aol.com>
wrote:

>In article <4be83610$0$31284$607ed4bc(a)cv.net>,
> "Tom D." <delo724(a)yahoo.com> wrote:
>
>> I have an HP 940c which has been great until now. Recently had it in storage
>> for almost 2 months. When I started it up again the graphics are now printing
>> misaligned. Went through the alignment procedure, but row "B" on the
>> alignment sheet never comes close to being aligned.
>> I take this to mean that it is so far out that software alone won't solve it.
>> I changed the cartridges as a precaution, but no luck.
>> Any idea how this happened or how to fix it - could find no information
>> anywhere.
>
>Tom-
>
>I'm not familiar with the 940c. Many printers have an ink head that
>travels back and forth on a metal bar. It prints a line of characters
>left to right, and then prints a reversed line when traveling right to
>left.
>
>If there was any kind of oil on the metal bar, it could collect paper
>dust. Some oil might also oxidize with the same result of slowing down
>the print head as it travels across, so characters printed one way might
>not line up with those printed during the return trip.
>
>If this happens to be the case, the solution may be to clean the bar.
>There may be a proper kind of lubricant to use, but it might also be
>designed so plastic riding on polished metal doesn't need any.
>
>Fred

For the series HP900 , HP recommends not to lubricate the rod. The bar
has a brass bushing that has natural lubrication but I would recommend
cleaning it with WD40. I have applied lubrication and the cartridge
carrier became noisy.
 | 
Pages: 1
Prev: Epson EPL-3000 printer... how to...
Next: MP530 using a lot of cyan and red