My 3rd sata drive
in [Linux Help]
|
From: Pascal Hambourg on 7 Jun 2010 16:23 J.O. Aho a �crit : > nomail@_INVALID_no.org wrote: >> >> The other idea of reading the dmsg is probably a good one too, not that >> I could understand most of it. The question is how to recover it? From within the initramfs rescue shell, if available. >> Every >> suspect boot is incomplete by definition and by the time I get a good >> one the boot message has been overwritten. Maybe if I boot another >> partition the second time with only two disks and then fish out the dmsg >> from the first? > > Much depends on your distro, some distros do save the dmesg to /var/log/dmesg This requires that /var/log is available, which is not going to happen when the final root fails to mount.
From: unruh on 7 Jun 2010 18:46 On 2010-06-07, J.O. Aho <user(a)example.net> wrote: > nomail@_INVALID_no.org wrote: >> On 06/06/2010 01:52 AM, J.O. Aho wrote: > >>>> I looked at the manual and it just talks 4 sata connectors which are >>>> numbered 1-4. I don't see any raid connectors as such, raid setup is in >>>> BIOS. >>> >>> Check that your "sda" is really connected to SATA1, so you haven't just at >>> some point put it in SATA4 and then changed boot order in BIOS. >>> This would explain why the booting don't work with your 3 disks setup, you >>> read the kernel from the machine with the kernel in hd0,0, but the kernel will >>> see the other disk as /dev/sda and that one does lack your high partition. >> >> I'll check this out, for now i'm busy prepping a eeeeeeeeeeeeeepc :-) >> >> The other idea of reading the dmsg is probably a good one too, not that >> I could understand most of it. The question is how to recover it? Every The old dmesg is saved as /var/log/dmesg.old Or if you boot from a cd boot disk, it will not be overwritten at all. >> suspect boot is incomplete by definition and by the time I get a good >> one the boot message has been overwritten. Maybe if I boot another >> partition the second time with only two disks and then fish out the dmsg >> from the first? > > Much depends on your distro, some distros do save the dmesg to /var/log/dmesg > and then you can read /var/log/dmesg.X what happen previous times you booted. >
From: nomail on 8 Jun 2010 15:58 On 06/07/2010 02:09 PM, J.O. Aho wrote: > nomail@_INVALID_no.org wrote: >> On 06/06/2010 01:52 AM, J.O. Aho wrote: > >>>> I looked at the manual and it just talks 4 sata connectors which are >>>> numbered 1-4. I don't see any raid connectors as such, raid setup is in >>>> BIOS. >>> >>> Check that your "sda" is really connected to SATA1, so you haven't just at >>> some point put it in SATA4 and then changed boot order in BIOS. >>> This would explain why the booting don't work with your 3 disks setup, you >>> read the kernel from the machine with the kernel in hd0,0, but the kernel will >>> see the other disk as /dev/sda and that one does lack your high partition. >> >> I'll check this out, for now i'm busy prepping a eeeeeeeeeeeeeepc :-) >> >> The other idea of reading the dmsg is probably a good one too, not that >> I could understand most of it. The question is how to recover it? Every >> suspect boot is incomplete by definition and by the time I get a good >> one the boot message has been overwritten. Maybe if I boot another >> partition the second time with only two disks and then fish out the dmsg >> from the first? > > Much depends on your distro, some distros do save the dmesg to /var/log/dmesg > and then you can read /var/log/dmesg.X what happen previous times you booted. > I got it as I thought I could, afterwards and from a another booted system. It's been a loooooooong series of sesssions. Your hunch that the sata pinouts 1&2/3&4 are somehow separated is beginning to look like a major suspect. The mobo manual is rather tight lipped about it. For years I've presumed that they were just that 4 nice sata drives and as I never had more than two I never ran into any trouble. Now 1 booted p-9 of disk 320gb-A in pos-1, 320gb-B in pos-2, 500gb in pos-3 "could not find /dev/sda9" 2 booted p-9 of disk 320B in pos-1, nothing in pos-2, 500 in pos-3 "could not find /dev/sda9" In the above only the 320gb-A driove had a bootable partition #9 Then 3 booted p-9 of 320gb-B in pos-1, nothing in pos-2/3, 2000gb-A in pos-4 I again got "could not find /dev/sda9" but the boot continued. Here I got results because I more or less successfully booted a suse-10.3 partition #9 ...but... on the 4th drive instead! fstab swap, fdisk against /dev/sda and such ALL confirmed the system was in fact on the 4th drive, 2000gb-A. Grub > root (hd0,14) [from within OS] "Error 18: selected cyl. not supported by BIOS" ..... not likely with a 320gb drive Grub > root (hd0,4) [from within OS] "..fs unknown, partition type 82" .... that's a swap partition on the 2000gb-A drive Contrary to what I had presumed, with 'a' kernel booted and grub loaded within it, the disk numbers given by grub are no longer the bios numbers. Giving the same arguments to grub before the boot would hit the correct disk and its partitions. That disk being 320gb and its #5 being vfat neither of the above errors surface until booted. All of the above confirms the finding that the 4th drive was being booted as the 'final' one :-) I can also boot with a disk in only #3 or only #4 or #3 & #4, there again the 2/3 border not being crossed. The only option might be to get another board, one that offers a straight series 4 or more SATA connectors and no PATA (just guessing if there are such boards). ======================================================= I then fished out the message. Looks like if a same-number bootable partition on the other side of 1&2 exists then it will boot instead. A kernel/modules conflict then arises and I'm only guessing that this may be because the target kernel has loaded but is now somewhere else and can't find the matching modules sets (?). .....a few long bits cut... Cannot find map file. No module symbols loaded - kernel modules not enabled. Cannot build symbol table - disabling symbol lookups klogd 1.4.1, log source = ksyslog started. <6>Initializing cgroup subsys cpuset <6>Initializing cgroup subsys cpu <5>Linux version 2.6.27.39-0.2-default (geeko(a)buildhost) (gcc version 4.3.2 [gcc-4_3-branch revision 141291] (SUSE Linux) ) #1 SMP 2009-11-23 12:57:38 +0100 <6>BIOS-provided physical RAM map: <6> BIOS-e820: 0000000000000000 - 000000000009f800 (usable) <6> BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) <6> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) <6> BIOS-e820: 0000000000100000 - 000000007fff0000 (usable) <6> BIOS-e820: 000000007fff0000 - 000000007fff3000 (ACPI NVS) <6> BIOS-e820: 000000007fff3000 - 0000000080000000 (ACPI data) <6> BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) <6> BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) <6>DMI 2.3 present. <5>Phoenix BIOS detected: BIOS may corrupt low RAM, working it around. <6>last_pfn = 0x7fff0 max_arch_pfn = 0x100000 <6>x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 <7>kernel direct mapping tables up to 38000000 @ 10000-15000 <6>RAMDISK: 37a14000 - 37fef83b <4>ACPI: RSDP 000F7560, 0014 (r0 Nvidia) <4>ACPI: RSDT 7FFF3040, 0034 (r1 Nvidia AWRDACPI 42302E31 AWRD 0) <4>ACPI: FACP 7FFF30C0, 0074 (r1 Nvidia AWRDACPI 42302E31 AWRD 0) <4>ACPI: DSDT 7FFF3180, 65F2 (r1 NVIDIA AWRDACPI 1000 MSFT 100000E) <4>ACPI: FACS 7FFF0000, 0040 <4>ACPI: SSDT 7FFF9880, 00D6 (r1 PTLTD POWERNOW 1 LTP 1) <4>ACPI: MCFG 7FFF99C0, 003C (r1 Nvidia AWRDACPI 42302E31 AWRD 0) <4>ACPI: APIC 7FFF97C0, 007C (r1 Nvidia AWRDACPI 42302E31 AWRD 0) <7>ACPI: Local APIC address 0xfee00000 <5>1151MB HIGHMEM available. <5>896MB LOWMEM available. <6> mapped low ram: 0 - 38000000 <6> low ram: 00000000 - 38000000 <6> bootmap 00011000 - 00018000 <6>(9 early reservations) ==> bootmem [0000000000 - 0038000000] <6> #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] <6> #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000] <6> #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000] <6> #3 [0000100000 - 0000638a5c] TEXT DATA BSS ==> [0000100000 - 0000638a5c] <6> #4 [0037a14000 - 0037fef83b] RAMDISK ==> [0037a14000 - 0037fef83b] <6> #5 [0000639000 - 000063c000] INIT_PG_TABLE ==> [0000639000 - 000063c000] <6> #6 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 - 0000100000] <6> #7 [0000010000 - 0000011000] PGTABLE ==> [0000010000 - 0000011000] <6> #8 [0000011000 - 0000018000] BOOTMAP ==> [0000011000 - 0000018000] <6>found SMP MP-table at [c00f54c0] 000f54c0 <4>Zone PFN ranges: <4> DMA 0x00000010 -> 0x00001000 <4> Normal 0x00001000 -> 0x00038000 <4> HighMem 0x00038000 -> 0x0007fff0 <4>Movable zone start PFN for each node <4>early_node_map[2] active PFN ranges <4> 0: 0x00000010 -> 0x0000009f <4> 0: 0x00000100 -> 0x0007fff0 <7>On node 0 totalpages: 524159 <7>free_area_init_node: node 0, pgdat c050d300, node_mem_map c1000240 <7> DMA zone: 3947 pages, LIFO batch:0 <7> Normal zone: 223300 pages, LIFO batch:31 <7> HighMem zone: 292304 pages, LIFO batch:31 <6>Using APIC driver default <6>Nvidia board detected. Ignoring ACPI timer override. <6>If you got timer trouble try acpi_use_timer_override <6>ACPI: PM-Timer IO Port: 0x4008 <7>ACPI: Local APIC address 0xfee00000 <6>ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) <6>ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled) <6>ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) <6>ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) <6>ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) <6>IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 <6>ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) <4>ACPI: BIOS IRQ0 pin2 override ignored. <6>ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) <6>ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge) <6>ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge) <7>ACPI: IRQ9 used by override. <7>ACPI: IRQ14 used by override. <7>ACPI: IRQ15 used by override. <4>Enabling APIC mode: Flat. Using 1 I/O APICs <6>Using ACPI (MADT) for SMP configuration information <6>SMP: Allowing 2 CPUs, 1 hotplug CPUs <7>mapped APIC to ffffb000 (fee00000) <7>mapped IOAPIC to ffffa000 (fec00000) <6>PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 <6>PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000 <6>PM: Registered nosave memory: 00000000000f0000 - 0000000000100000 <6>Allocating PCI resources starting at 88000000 (gap: 80000000:60000000) <6>PERCPU: Allocating 37916 bytes of per cpu data <7>NR_CPUS: 32, nr_cpu_ids: 2, nr_node_ids 1 <4>Built 1 zonelists in Zone order, mobility grouping on. Total pages: 519551 <5>Kernel command line: root=/dev/sda9 vga=0x31a splash=0 3 <6>Enabling fast FPU save and restore... done. <6>Enabling unmasked SIMD FPU exception support... done. <6>Initializing CPU#0 <4>PID hash table entries: 4096 (order: 12, 16384 bytes) <6>TSC: PIT calibration confirmed by PMTIMER. <6>TSC: using PIT calibration value <4>Detected 2010.260 MHz processor. <7>spurious 8259A interrupt: IRQ7. <4>Console: colour dummy device 80x25 <6>console [tty0] enabled <6>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>Memory: 2064936k/2097088k available (2303k kernel code, 30724k reserved, 1931k data, 280k init, 1179584k highmem) <6>virtual kernel memory layout: <6> fixmap : 0xffdf7000 - 0xfffff000 (2080 kB) <6> pkmap : 0xff400000 - 0xff800000 (4096 kB) <6> vmalloc : 0xf8800000 - 0xff3fe000 ( 107 MB) <6> lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) <6> .init : 0xc052b000 - 0xc0571000 ( 280 kB) <6> .data : 0xc033ff93 - 0xc0522cd0 (1931 kB) <6> .text : 0xc0100000 - 0xc033ff93 (2303 kB) <6>Checking if this processor honours the WP bit even in supervisor mode...Ok. <7>CPA: page pool initialized 1 of 1 pages preallocated <6>Calibrating delay loop (skipped), value calculated using timer frequency.. 4020.52 BogoMIPS (lpj=8041040) <4>kdb version 4.4 by Keith Owens, Scott Lurndal. Copyright SGI, All Rights Reserved <6>Security Framework initialized <6>AppArmor: AppArmor initialized <4>Mount-cache hash table entries: 512 <6>Initializing cgroup subsys ns <6>Initializing cgroup subsys cpuacct <6>Initializing cgroup subsys memory <6>Initializing cgroup subsys devices <6>Initializing cgroup subsys freezer <6>CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) <6>CPU: L2 Cache: 512K (64 bytes/line) <6>Intel machine check architecture supported. <6>Intel machine check reporting enabled on CPU#0. <6>Checking 'hlt' instruction... OK. <6>SMP alternatives: switching to UP code <6>ACPI: Core revision 20080609 <6>ACPI: Checking initramfs for custom DSDT <4>Parsing all Control Methods: <4>Table [DSDT](id 0001) - 988 Objects with 86 Devices 316 Methods 37 Regions <4>Parsing all Control Methods: <4>Table [SSDT](id 0002) - 3 Objects with 0 Devices 0 Methods 0 Regions <4> tbxface-0596 [00] tb_load_namespace : ACPI Tables successfully acquired <4>evxfevnt-0091 [00] enable : Transition to ACPI mode successful <4>ENABLING IO-APIC IRQs <6>..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1 <6>CPU0: AMD Athlon(tm) 64 Processor 3200+ stepping 02 <6>Brought up 1 CPUs <6>Total of 1 processors activated (4020.52 BogoMIPS). <7>CPU0 attaching NULL sched-domain. <6>net_namespace: 1044 bytes <6>NET: Registered protocol family 16 <6>ACPI: bus type pci registered <5>PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 <5>PCI: MCFG area at e0000000 reserved in E820 <6>PCI: Using MMCONFIG for extended config space <6>PCI: Using configuration type 1 for base access <5>perfmon: version 2.82 <5>perfmon: CPU hotplug support enabled <4>evgpeblk-0957 [00] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int 0x9 <4>evgpeblk-0957 [00] ev_create_gpe_block : GPE 20 to 5F [_GPE] 8 regs on int 0x9 <7>ACPI: EC: Look up EC in DSDT <4>Completing Region/Field/Buffer/Package initialization:................................................................................................................................................. <4>Initialized 33/37 Regions 9/9 Fields 35/35 Buffers 68/79 Packages (1000 nodes) <4>Initializing Device/Processor/Thermal objects by executing _INI methods:... <4>Executed 3 _INI methods requiring 1 _STA executions (examined 91 objects) <4>evgpeblk-1054 [00] ev_initialize_gpe_bloc: Found 8 Wake, Enabled 0 Runtime GPEs in this block <4>evgpeblk-1054 [00] ev_initialize_gpe_bloc: Found 0 Wake, Enabled 0 Runtime GPEs in this block <6>ACPI: Interpreter enabled <6>ACPI: (supports S0 S1 S3 S4 S5) <6>ACPI: Using IOAPIC for interrupt routing <6>ACPI: PCI Root Bridge [PCI0] (0000:00) <6>HPET not enabled in BIOS. You might try hpet=force boot option <7>PCI: 0000:00:01.1 reg 10 io port: [e400, e41f] <7>PCI: 0000:00:01.1 reg 20 io port: [4c00, 4c3f] <7>PCI: 0000:00:01.1 reg 24 io port: [4c40, 4c7f] <6>pci 0000:00:01.1: PME# supported from D3hot D3cold <6>pci 0000:00:01.1: PME# disabled <7>PCI: 0000:00:02.0 reg 10 32bit mmio: [d8004000, d8004fff] <7>pci 0000:00:02.0: supports D1 <7>pci 0000:00:02.0: supports D2 <6>pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold <6>pci 0000:00:02.0: PME# disabled <7>PCI: 0000:00:02.1 reg 10 32bit mmio: [feb00000, feb000ff] <7>pci 0000:00:02.1: supports D1 <7>pci 0000:00:02.1: supports D2 <6>pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold <6>pci 0000:00:02.1: PME# disabled <7>PCI: 0000:00:04.0 reg 10 io port: [dc00, dcff] <7>PCI: 0000:00:04.0 reg 14 io port: [e000, e0ff] <7>PCI: 0000:00:04.0 reg 18 32bit mmio: [d8003000, d8003fff] <7>pci 0000:00:04.0: supports D1 <7>pci 0000:00:04.0: supports D2 <7>PCI: 0000:00:06.0 reg 20 io port: [f000, f00f] <7>PCI: 0000:00:07.0 reg 10 io port: [9f0, 9f7] <7>PCI: 0000:00:07.0 reg 14 io port: [bf0, bf3] <7>PCI: 0000:00:07.0 reg 18 io port: [970, 977] <7>PCI: 0000:00:07.0 reg 1c io port: [b70, b73] <7>PCI: 0000:00:07.0 reg 20 io port: [d800, d80f] <7>PCI: 0000:00:07.0 reg 24 32bit mmio: [d8002000, d8002fff] <7>PCI: 0000:00:08.0 reg 10 io port: [9e0, 9e7] <7>PCI: 0000:00:08.0 reg 14 io port: [be0, be3] <7>PCI: 0000:00:08.0 reg 18 io port: [960, 967] <7>PCI: 0000:00:08.0 reg 1c io port: [b60, b63] <7>PCI: 0000:00:08.0 reg 20 io port: [c400, c40f] <7>PCI: 0000:00:08.0 reg 24 32bit mmio: [d8001000, d8001fff] <7>PCI: 0000:00:0a.0 reg 10 32bit mmio: [d8000000, d8000fff] <7>PCI: 0000:00:0a.0 reg 14 io port: [b000, b007] <7>pci 0000:00:0a.0: supports D1 <7>pci 0000:00:0a.0: supports D2 <6>pci 0000:00:0a.0: PME# supported from D0 D1 D2 D3hot D3cold <6>pci 0000:00:0a.0: PME# disabled <6>pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold <6>pci 0000:00:0b.0: PME# disabled <6>pci 0000:00:0c.0: PME# supported from D0 D1 D2 D3hot D3cold <6>pci 0000:00:0c.0: PME# disabled <6>pci 0000:00:0d.0: PME# supported from D0 D1 D2 D3hot D3cold <6>pci 0000:00:0d.0: PME# disabled <6>pci 0000:00:0e.0: PME# supported from D0 D1 D2 D3hot D3cold <6>pci 0000:00:0e.0: PME# disabled <6>pci 0000:00:09.0: transparent bridge <7>PCI: 0000:01:00.0 reg 10 32bit mmio: [d0000000, d3ffffff] <7>PCI: 0000:01:00.0 reg 14 64bit mmio: [c0000000, cfffffff] <7>PCI: 0000:01:00.0 reg 1c 64bit mmio: [d4000000, d4ffffff] <7>PCI: 0000:01:00.0 reg 30 32bit mmio: [d5000000, d501ffff] <4>Pre-1.1 PCIe device detected, disable ASPM for 0000:00:0e.0. It can be enabled forcedly with 'pcie_aspm=force' <7>PCI: bridge 0000:00:0e.0 32bit mmio: [d0000000, d7ffffff] <7>PCI: bridge 0000:00:0e.0 64bit mmio pref: [c0000000, cfffffff] <7>bus 00 -> node 0 <7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] <7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] <6>ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. <6>ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. <6>ACPI: PCI Interrupt Link [LNK3] (IRQs *3 4 5 7 9 10 11 12 14 15) <6>ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. <6>ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. <6>ACPI: PCI Interrupt Link [LUBA] (IRQs *3 4 5 7 9 10 11 12 14 15) <6>ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. <6>ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 *5 7 9 10 11 12 14 15) <6>ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 7 9 10 *11 12 14 15) <6>ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. <6>ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 *5 7 9 10 11 12 14 15) <6>ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 7 9 10 *11 12 14 15) <6>ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. <6>ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 7 9 10 *11 12 14 15) <6>ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 *5 7 9 10 11 12 14 15) <6>ACPI: PCI Interrupt Link [LPCA] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. <6>ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled. <6>ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled. <6>ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0 <6>ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled. <6>ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled. <6>ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0 <6>ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled. <6>ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0 <6>ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0 <6>ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled. <6>ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0 <6>ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0 <6>ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled. <6>ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0 <6>ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0 <6>ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled. <6>Linux Plug and Play Support v0.97 (c) Adam Belay <6>pnp: PnP ACPI init <6>ACPI: bus type pnp registered <6>pnp: PnP ACPI: found 15 devices <6>ACPI: ACPI bus type pnp unregistered <6>PnPBIOS: Disabled by ACPI PNP <6>PCI: Using ACPI for IRQ routing <6>AppArmor: AppArmor Filesystem Enabled <4>ACPI: RTC can wake from S4 <6>system 00:01: ioport range 0x4000-0x407f has been reserved <6>system 00:01: ioport range 0x4080-0x40ff has been reserved <6>system 00:01: ioport range 0x4400-0x447f has been reserved <6>system 00:01: ioport range 0x4480-0x44ff has been reserved <6>system 00:01: ioport range 0x4800-0x487f has been reserved <6>system 00:01: ioport range 0x4880-0x48ff has been reserved <6>system 00:02: ioport range 0x4d0-0x4d1 has been reserved <6>system 00:02: ioport range 0x800-0x87f has been reserved <6>system 00:02: ioport range 0x290-0x297 has been reserved <6>system 00:0d: iomem range 0xe0000000-0xefffffff could not be reserved <6>system 00:0e: iomem range 0xf0000-0xf3fff could not be reserved <6>system 00:0e: iomem range 0xf4000-0xf7fff could not be reserved <6>system 00:0e: iomem range 0xf8000-0xfbfff could not be reserved <6>system 00:0e: iomem range 0xfc000-0xfffff could not be reserved <6>system 00:0e: iomem range 0x7fff0000-0x7fffffff could not be reserved <6>system 00:0e: iomem range 0xffff0000-0xffffffff could not be reserved <6>system 00:0e: iomem range 0x0-0x9ffff could not be reserved <6>system 00:0e: iomem range 0x100000-0x7ffeffff could not be reserved <6>system 00:0e: iomem range 0xfec00000-0xfec00fff could not be reserved <6>system 00:0e: iomem range 0xfee00000-0xfeefffff could not be reserved <6>system 00:0e: iomem range 0xfefff000-0xfeffffff could not be reserved <6>system 00:0e: iomem range 0xfff80000-0xfff80fff could not be reserved <6>system 00:0e: iomem range 0xfff90000-0xfffbffff could not be reserved <6>system 00:0e: iomem range 0xfffed000-0xfffeffff could not be reserved <6>pci 0000:00:09.0: PCI bridge, secondary bus 0000:05 <6>pci 0000:00:09.0: IO window: disabled <6>pci 0000:00:09.0: MEM window: disabled <6>pci 0000:00:09.0: PREFETCH window: disabled <6>pci 0000:00:0b.0: PCI bridge, secondary bus 0000:04 <6>pci 0000:00:0b.0: IO window: disabled <6>pci 0000:00:0b.0: MEM window: disabled <6>pci 0000:00:0b.0: PREFETCH window: disabled <6>pci 0000:00:0c.0: PCI bridge, secondary bus 0000:03 <6>pci 0000:00:0c.0: IO window: disabled <6>pci 0000:00:0c.0: MEM window: disabled <6>pci 0000:00:0c.0: PREFETCH window: disabled <6>pci 0000:00:0d.0: PCI bridge, secondary bus 0000:02 <6>pci 0000:00:0d.0: IO window: disabled <6>pci 0000:00:0d.0: MEM window: disabled <6>pci 0000:00:0d.0: PREFETCH window: disabled <6>pci 0000:00:0e.0: PCI bridge, secondary bus 0000:01 <6>pci 0000:00:0e.0: IO window: disabled <6>pci 0000:00:0e.0: MEM window: 0xd0000000-0xd7ffffff <6>pci 0000:00:0e.0: PREFETCH window: 0x000000c0000000-0x000000cfffffff <7>pci 0000:00:09.0: setting latency timer to 64 <7>pci 0000:00:0b.0: setting latency timer to 64 <7>pci 0000:00:0c.0: setting latency timer to 64 <7>pci 0000:00:0d.0: setting latency timer to 64 <7>pci 0000:00:0e.0: setting latency timer to 64 <6>bus: 00 index 0 io port: [0, ffff] <6>bus: 00 index 1 mmio: [0, ffffffff] <6>bus: 05 index 0 mmio: [0, 0] <6>bus: 05 index 1 mmio: [0, 0] <6>bus: 05 index 2 mmio: [0, 0] <6>bus: 05 index 3 io port: [0, ffff] <6>bus: 05 index 4 mmio: [0, ffffffff] <6>bus: 04 index 0 mmio: [0, 0] <6>bus: 04 index 1 mmio: [0, 0] <6>bus: 04 index 2 mmio: [0, 0] <6>bus: 04 index 3 mmio: [0, 0] <6>bus: 03 index 0 mmio: [0, 0] <6>bus: 03 index 1 mmio: [0, 0] <6>bus: 03 index 2 mmio: [0, 0] <6>bus: 03 index 3 mmio: [0, 0] <6>bus: 02 index 0 mmio: [0, 0] <6>bus: 02 index 1 mmio: [0, 0] <6>bus: 02 index 2 mmio: [0, 0] <6>bus: 02 index 3 mmio: [0, 0] <6>bus: 01 index 0 mmio: [0, 0] <6>bus: 01 index 1 mmio: [d0000000, d7ffffff] <6>bus: 01 index 2 mmio: [c0000000, cfffffff] <6>bus: 01 index 3 mmio: [0, 0] <6>NET: Registered protocol family 2 <6>IP route cache hash table entries: 32768 (order: 5, 131072 bytes) <6>TCP established hash table entries: 131072 (order: 8, 1048576 bytes) <6>TCP bind hash table entries: 65536 (order: 7, 524288 bytes) <6>TCP: Hash tables configured (established 131072 bind 65536) <6>TCP reno registered <6>NET: Registered protocol family 1 <6>Unpacking initramfs...<7>Switched to high resolution mode on CPU 0 <4> done <6>Freeing initrd memory: 5998k freed <6>Machine check exception polling timer started. <6>audit: initializing netlink socket (disabled) <5>type=2000 audit(1275989476.580:1): initialized <4>highmem bounce pool size: 64 pages <6>HugeTLB registered 4 MB page size, pre-allocated 0 pages <5>VFS: Disk quotas dquot_6.5.1 <4>Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>msgmni has been set to 435 <6>Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) <6>io scheduler noop registered <6>io scheduler anticipatory registered <6>io scheduler deadline registered <6>io scheduler cfq registered (default) <6>perfmon: added sampling format default <6>pci 0000:00:00.0: Enabling HT MSI Mapping <6>pci 0000:00:0b.0: Enabling HT MSI Mapping <6>pci 0000:00:0b.0: Found enabled HT MSI Mapping <6>pci 0000:00:0b.0: Linking AER extended capability <6>pci 0000:00:0c.0: Enabling HT MSI Mapping <6>pci 0000:00:0c.0: Found enabled HT MSI Mapping <6>pci 0000:00:0c.0: Linking AER extended capability <6>pci 0000:00:0d.0: Enabling HT MSI Mapping <6>pci 0000:00:0d.0: Found enabled HT MSI Mapping <6>pci 0000:00:0d.0: Linking AER extended capability <6>pci 0000:00:0e.0: Enabling HT MSI Mapping <6>pci 0000:00:0e.0: Found enabled HT MSI Mapping <6>pci 0000:00:0e.0: Linking AER extended capability <7>pci 0000:01:00.0: Boot video device <7>pcieport-driver 0000:00:0b.0: setting latency timer to 64 <6>pcieport-driver 0000:00:0b.0: found MSI capability <7>pci_express 0000:00:0b.0:pcie00: allocate port service <7>pci_express 0000:00:0b.0:pcie03: allocate port service <7>pcieport-driver 0000:00:0c.0: setting latency timer to 64 <6>pcieport-driver 0000:00:0c.0: found MSI capability <7>pci_express 0000:00:0c.0:pcie00: allocate port service <7>pci_express 0000:00:0c.0:pcie03: allocate port service <7>pcieport-driver 0000:00:0d.0: setting latency timer to 64 <6>pcieport-driver 0000:00:0d.0: found MSI capability <7>pci_express 0000:00:0d.0:pcie00: allocate port service <7>pci_express 0000:00:0d.0:pcie03: allocate port service <7>pcieport-driver 0000:00:0e.0: setting latency timer to 64 <6>pcieport-driver 0000:00:0e.0: found MSI capability <7>pci_express 0000:00:0e.0:pcie00: allocate port service <7>pci_express 0000:00:0e.0:pcie03: allocate port service <6>vesafb: framebuffer at 0xc0000000, mapped to 0xf8880000, using 10240k, total 262144k ....continued
From: nomail on 8 Jun 2010 15:58 ....continuing <6>vesafb: mode is 1280x1024x16, linelength=2560, pages=1 <6>vesafb: protected mode interface info at c000:d5c0 <6>vesafb: pmi: set display start = c00cd5f6, set palette = c00cd660 <6>vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da <6>vesafb: scrolling: redraw <6>vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 <6>bootsplash 3.1.6-2004/03/31: looking for picture... <6>bootsplash: silentjpeg size 113709 bytes <6>bootsplash: ...found (1280x1024, 43709 bytes, v3). <4>Console: switching to colour frame buffer device 160x64 <6>fb0: VESA VGA frame buffer device <6>isapnp: Scanning for PnP cards... <6>isapnp: No Plug & Play device found <6>Serial: 8250/16550 driver8 ports, IRQ sharing enabled <6>serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A <6>00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A <6>PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 <4>PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp <6>serio: i8042 KBD port at 0x60,0x64 irq 1 <6>mice: PS/2 mouse device common for all mice <6>cpuidle: using governor ladder <6>cpuidle: using governor menu <6>TCP cubic registered <4>Using IPI No-Shortcut mode <4>registered taskstats version 1 <6>Freeing unused kernel memory: 280k freed <6>Write protecting the kernel text: 2304k <6>Write protecting the kernel read-only data: 1740k <6>input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0 <6>processor ACPI_CPU:00: registered as cooling_device0 <6>thermal LNXTHERM:01: registered as thermal_zone0 <6>ACPI: Thermal Zone [THRM] (40 C) <6>ACPI: No dock devices found. <5>SCSI subsystem initialized <7>libata version 3.00 loaded. <7>sata_nv 0000:00:07.0: version 3.5 <4>ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23 <6>sata_nv 0000:00:07.0: PCI INT A -> Link[APSI] -> GSI 23 (level, low) -> IRQ 23 <7>sata_nv 0000:00:07.0: setting latency timer to 64 <6>scsi0 : sata_nv <6>scsi1 : sata_nv <6>ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd800 irq 23 <6>ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd808 irq 23 <6>ata1: SATA link down (SStatus 0 SControl 300) <6>ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) <6>ata2.00: ATA-8: WDC WD20EARS-00S8B1, 80.00A80, max UDMA/133 <6>ata2.00: 3907029168 sectors, multi 1: LBA48 NCQ (depth 0/32) <6>ata2.00: configured for UDMA/133 <5>scsi 1:0:0:0: Direct-Access ATA WDC WD20EARS-00S 80.0 PQ: 0 ANSI: 5 <4>ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 22 <6>sata_nv 0000:00:08.0: PCI INT A -> Link[APSJ] -> GSI 22 (level, low) -> IRQ 22 <7>sata_nv 0000:00:08.0: setting latency timer to 64 <6>scsi2 : sata_nv <6>scsi3 : sata_nv <6>ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xc400 irq 22 <6>ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xc408 irq 22 <6>ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) <6>ata3.00: ATA-7: WDC WD3200AAKS-22SBA0, 12.01B01, max UDMA/133 <6>ata3.00: 625142448 sectors, multi 1: LBA48 NCQ (depth 0/32) <6>ata3.00: configured for UDMA/133 <6>ata4: SATA link down (SStatus 0 SControl 300) <5>scsi 2:0:0:0: Direct-Access ATA WDC WD3200AAKS-2 12.0 PQ: 0 ANSI: 5 <7>pata_amd 0000:00:06.0: version 0.3.10 <7>pata_amd 0000:00:06.0: setting latency timer to 64 <6>scsi4 : pata_amd <6>scsi5 : pata_amd <6>ata5: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14 <6>ata6: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15 <6>ata5.00: ATAPI: DVD RW DRU-820A, 1.0c, max UDMA/66 <7>ata5: nv_mode_filter: 0x1f39f&0x1f01f->0x1f01f, BIOS=0x1f000 (0xc5000000) ACPI=0x1f01f (30:600:0x13) <6>ata5.00: configured for UDMA/66 <5>scsi 4:0:0:0: CD-ROM SONY DVD RW DRU-820A 1.0c PQ: 0 ANSI: 5 <6>Uniform Multi-Platform E-IDE driver <6>fan PNP0C0B:00: registered as cooling_device1 <6>ACPI: Fan [FAN] (on) <6>BIOS EDD facility v0.16 2004-Jun-25, 2 devices found <6>udevd version 128 started <6>usbcore: registered new interface driver usbfs <6>usbcore: registered new interface driver hub <6>usbcore: registered new device driver usb <4>ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21 <6>ehci_hcd 0000:00:02.1: PCI INT B -> Link[APCL] -> GSI 21 (level, low) -> IRQ 21 <7>ehci_hcd 0000:00:02.1: setting latency timer to 64 <6>ehci_hcd 0000:00:02.1: EHCI Host Controller <6>ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1 <6>ehci_hcd 0000:00:02.1: debug port 1 <7>ehci_hcd 0000:00:02.1: cache line size of 64 is not supported <6>ehci_hcd 0000:00:02.1: irq 21, io mem 0xfeb00000 <7>ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver <6>ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 <6>usb usb1: configuration #1 chosen from 1 choice <6>hub 1-0:1.0: USB hub found <6>hub 1-0:1.0: 10 ports detected <5>sd 1:0:0:0: [sda] 3907029168 512-byte hardware sectors: (2.00 TB/1.81 TiB) <5>sd 1:0:0:0: [sda] Write Protect is off <7>sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00 <5>sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <5>sd 1:0:0:0: [sda] 3907029168 512-byte hardware sectors: (2.00 TB/1.81 TiB) <5>sd 1:0:0:0: [sda] Write Protect is off <7>sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00 <5>sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <6> sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 sda13 sda14<6>usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 <6>usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>usb usb1: Product: EHCI Host Controller <6>usb usb1: Manufacturer: Linux 2.6.27.39-0.2-default ehci_hcd <6>usb usb1: SerialNumber: 0000:00:02.1 <4>ACPI: PCI Interrupt Link [APCF] enabled at IRQ 20 <6>ohci_hcd 0000:00:02.0: PCI INT A -> Link[APCF] -> GSI 20 (level, low) -> IRQ 20 <7>ohci_hcd 0000:00:02.0: setting latency timer to 64 <6>ohci_hcd 0000:00:02.0: OHCI Host Controller <6>ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2 <6>ohci_hcd 0000:00:02.0: irq 20, io mem 0xd8004000 <4> sda15 > <5>sd 1:0:0:0: [sda] Attached SCSI disk <5>sd 2:0:0:0: [sdb] 625142448 512-byte hardware sectors: (320 GB/298 GiB) <5>sd 2:0:0:0: [sdb] Write Protect is off <7>sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00 <5>sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <5>sd 2:0:0:0: [sdb] 625142448 512-byte hardware sectors: (320 GB/298 GiB) <5>sd 2:0:0:0: [sdb] Write Protect is off <7>sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00 <5>sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA <6> sdb: sdb1 sdb2 sdb3 sdb4 <<6>usb usb2: configuration #1 chosen from 1 choice <6>hub 2-0:1.0: USB hub found <6>hub 2-0:1.0: 10 ports detected <4> sdb5 sdb6 sdb7 sdb8 sdb9 sdb10 sdb11 sdb12 sdb13 sdb14 sdb15 > <5>sd 2:0:0:0: [sdb] Attached SCSI disk <6>usb 1-4: new high speed USB device using ehci_hcd and address 3 <6>usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 <6>usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>usb usb2: Product: OHCI Host Controller <6>usb usb2: Manufacturer: Linux 2.6.27.39-0.2-default ohci_hcd <6>usb usb2: SerialNumber: 0000:00:02.0 <6>usb 1-4: configuration #1 chosen from 1 choice <6>usb 1-4: New USB device found, idVendor=04e8, idProduct=3425 <6>usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 <6>usb 1-4: Product: CLX-216x Series <6>usb 1-4: Manufacturer: Samsung Electronics Co., Ltd. <6>usb 1-4: SerialNumber: 9561BAIQ900177Y. <6>usb 1-7: new high speed USB device using ehci_hcd and address 4 <6>usb 1-7: configuration #1 chosen from 1 choice <6>usb 1-7: New USB device found, idVendor=058f, idProduct=6362 <6>usb 1-7: New USB device strings: Mfr=1, Product=2, SerialNumber=3 <6>usb 1-7: Product: Mass Storage Device <6>usb 1-7: Manufacturer: Generic <6>usb 1-7: SerialNumber: 058F312D81B <6>usb 2-2: new low speed USB device using ohci_hcd and address 2 <6>usb 2-2: configuration #1 chosen from 1 choice <6>usb 2-2: New USB device found, idVendor=046d, idProduct=c00e <6>usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 <6>usb 2-2: Product: USB-PS/2 Optical Mouse <6>usb 2-2: Manufacturer: Logitech <6>usb 2-9: new low speed USB device using ohci_hcd and address 3 <6>usb 2-9: configuration #1 chosen from 1 choice <6>usb 2-9: New USB device found, idVendor=046d, idProduct=c207 <6>usb 2-9: New USB device strings: Mfr=4, Product=32, SerialNumber=0 <6>usb 2-9: Product: WingMan Extreme Digital 3D <6>usb 2-9: Manufacturer: Logitech Inc. <6>usbcore: registered new interface driver hiddev <6>input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:02.0/usb2/2-2/2-2:1.0/input/input1 <6>input,hidraw0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:02.0-2 <4>usbhid: timeout initializing reports <6>input: Logitech Inc. WingMan Extreme Digital 3D as /devices/pci0000:00/0000:00:02.0/usb2/2-9/2-9:1.0/input/input2 <6>input,hidraw1: USB HID v1.00 Joystick [Logitech Inc. WingMan Extreme Digital 3D] on usb-0000:00:02.0-9 <6>usbcore: registered new interface driver usbhid <6>usbhid: v2.6:USB HID core driver <5>REISERFS (device sda9): found reiserfs format "3.6" with standard journal <5>REISERFS (device sda9): using ordered data mode <4>reiserfs: using flush barriers <5>REISERFS (device sda9): journal params: device sda9, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 <5>REISERFS (device sda9): checking transaction log (sda9) <5>REISERFS (device sda9): Using r5 hash to sort names <6>Adding 2104472k swap on /dev/sda5. Priority:-1 extents:1 across:2104472k Kernel logging (ksyslog) stopped. Kernel log daemon terminating. Boot logging started on /dev/tty1(/dev/console) at Tue Jun 8 09:31:33 2010 resume device not found (ignoring) Waiting for device /dev/sda9 to appear: ok fsck 1.41.1 (01-Sep-2008) [/sbin/fsck.reiserfs (1) -- /] fsck.reiserfs -a /dev/sda9 Reiserfs super block in block 16 on 0x809 of format 3.6 with standard journal Blocks (total/free): 5243200/4683874 by 4096 bytes Filesystem is clean fsck succeeded. Mounting root device read-write. Mounting root /dev/sda9 Boot logging started on /dev/tty1(/dev/console (deleted)) at Tue Jun 8 05:31:35 2010 done Starting udevd done Loading required kernel modules doneActivating swap-devices in /etc/fstab... donemount: according to mtab, /dev/sda9 is already mounted on / Activating device mapper... FATAL: Could not load /lib/modules/2.6.27.39-0.2-default/modules.dep: No such file or directory failed Starting MD Raid unused Checking file systems... fsck 1.40.2 (12-Jul-2007) donedone Mounting local file systems... proc on /proc type proc (rw) sysfs on /sys type sysfs (rw) debugfs on /sys/kernel/debug type debugfs (rw) udev on /dev type tmpfs (rw) FATAL: Could not load /lib/modules/2.6.27.39-0.2-default/modules.dep: No such file or directory devpts on /dev/pts type devpts (rw,mode=0620,gid=5) nothing was mounted doneActivating remaining swap-devices in /etc/fstab... done<notice>killproc: kill(709,29) Creating /var/log/boot.msg doneSetting up the hardware clockdone Setting up hostname 'linux'done Setting up loopback interface Retry device configurationdone Configuring serial ports... /dev/ttyS0 at 0x03f8 (irq = 4) is a 16550A Configured serial ports done lo lo IP address: 127.0.0.1/8 Checking for network time protocol daemon (NTPD): unused Setting current sysctl status from /etc/sysctl.conf net.ipv4.icmp_echo_ignore_broadcasts = 1 net.ipv4.conf.all.rp_filter = 1 fs.inotify.max_user_watches = 65536 done Enabling syn flood protectiondone Disabling IP forwardingdone done Can't determine current runlevel done System Boot Control: The system has been set up Skipped features: boot.md System Boot Control: Running /etc/init.d/boot.local done<notice>killproc: kill(709,3) INIT: Entering runlevel: 3 Boot logging started on /dev/tty1(/dev/console) at Tue Jun 8 09:31:50 2010 Master Resource Control: previous runlevel: N, switching to runlevel: 3 Starting D-Bus daemonUnknown username "gdm" in message bus configuration file done <notice>startproc: execve (/sbin/resmgrd) [ /sbin/resmgrd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=3 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=0 SPLASH=no ROOTFS_BLKDEV=/dev/sda9 _=/sbin/startproc DAEMON=/sbin/resmgrd ] Starting resource managerdone Starting acpid <notice>startproc: execve (/sbin/acpid) [ /sbin/acpid ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=3 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=0 SPLASH=no ROOTFS_BLKDEV=/dev/sda9 _=/sbin/startproc DAEMON=/sbin/acpid ] acpid: starting up acpid: 0 rules loaded done <notice>startproc: execve (/usr/sbin/console-kit-daemon) [ /usr/sbin/console-kit-daemon ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=3 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=0 SPLASH=no ROOTFS_BLKDEV=/dev/sda9 _=/sbin/startproc DAEMON=/usr/sbin/console-kit-daemon ] Starting ConsoleKitdone Starting HAL daemon<notice>startproc: execve (/usr/sbin/hald) [ /usr/sbin/hald --daemon=yes ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=3 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=0 SPLASH=no ROOTFS_BLKDEV=/dev/sda9 _=/sbin/startproc DAEMON=/usr/sbin/hald ] done Loading CPUFreq modules (CPUFreq not supported) modprobe: FATAL: Could not load /lib/modules/2.6.27.39-0.2-default/modules.dep: No such file or directory acpid: client connected from 1684[101:102] acpid: 1 client rule loaded Starting irqbalance unused Starting Firewall Initialization (phase 1 of 2) SuSEfirewall2: Warning: ip6tables does not support state matching. Extended IPv6 support disabled. SuSEfirewall2: Warning: Kernel lacks support for IPv6 REJECT target! Using DROP for IPv6 instead. FATAL: Could not load /lib/modules/2.6.27.39-0.2-default/modules.dep: No such file or directory FATAL: Could not load /lib/modules/2.6.27.39-0.2-default/modules.dep: No such file or directory FATAL: Could not load /lib/modules/2.6.27.39-0.2-default/modules.dep: No such file or directory iptables-batch v1.3.8: can't initialize iptables table `filter': iptables who? (do you need to insmod?) ............ FATAL: Could not load /lib/modules/2.6.27.39-0.2-default/modules.dep: No such file or directory iptables v1.3.8: can't initialize iptables table `filter': iptables who? (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. done Initializing random number generatordone Loading keymap i386/qwerty/us.map.gz doneLoading compose table latin1.adddone Start Unicode mode doneLoading console font lat9w-16.psfu -m trivial G0:loadable doneSetting up network interfaces: lo lo IP address: 127.0.0.1/8 Checking for network time protocol daemon (NTPD): unused lo doneWaiting for mandatory devices: eth0 __NSC__ 19 18 17 16 15 14 13 12 11 10 9 8 7 5 4 3 2 1 0 eth0 No interface found failedSetting up service network . . . . . . . . . . . . . . . .failed <notice>startproc: execve (/usr/sbin/avahi-daemon) [ /usr/sbin/avahi-daemon -D ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=3 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=0 SPLASH=no ROOTFS_BLKDEV=/dev/sda9 _=/sbin/startproc DAEMON=/usr/sbin/avahi-daemon ] <notice>startproc: execve (/sbin/syslog-ng) [ /sbin/syslog-ng ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=3 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=0 SPLASH=no ROOTFS_BLKDEV=/dev/sda9 _=/sbin/startproc DAEMON=/sbin/syslog-ng ] <notice>startproc: execve (/usr/sbin/sshd) [ /usr/sbin/sshd -o PidFile=/var/run/sshd.init.pid ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=3 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=0 SPLASH=no ROOTFS_BLKDEV=/dev/sda9 _=/sbin/startproc DAEMON=/usr/sbin/sshd ] Starting SSH daemondone <notice>startproc: execve (/sbin/klogd) [ /sbin/klogd -c 1 -x -x ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=3 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=0 SPLASH=no ROOTFS_BLKDEV=/dev/sda9 _=/sbin/startproc DAEMON=/sbin/klogd ] Starting syslog servicesdone <notice>startproc: execve (/sbin/auditd) [ /sbin/auditd -s disable ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=3 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=0 SPLASH=no ROOTFS_BLKDEV=/dev/sda9 _=/sbin/startproc DAEMON=/sbin/auditd ] Starting Avahi daemon.done Starting auditd done <notice>startproc: execve (/usr/sbin/avahi-dnsconfd) [ /usr/sbin/avahi-dnsconfd -D ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=3 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=0 SPLASH=no ROOTFS_BLKDEV=/dev/sda9 _=/sbin/startproc DAEMON=/usr/sbin/avahi-dnsconfd ] Starting Avahi DNS Configuration daemondone <notice>startproc: execve (/usr/sbin/nscd) [ /usr/sbin/nscd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=3 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=0 SPLASH=no ROOTFS_BLKDEV=/dev/sda9 _=/sbin/startproc DAEMON=/usr/sbin/nscd ] Starting Name Service Cache Daemondone <notice>startproc: execve (/sbin/portmap) [ /sbin/portmap ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=3 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=0 SPLASH=no ROOTFS_BLKDEV=/dev/sda9 _=/sbin/startproc DAEMON=/sbin/portmap ] Starting RPC portmap daemondone <notice>startproc: execve (/usr/sbin/cupsd) [ /usr/sbin/cupsd ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=3 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=0 SPLASH=no ROOTFS_BLKDEV=/dev/sda9 _=/sbin/startproc DAEMON=/usr/sbin/cupsd ] Starting cupsddone <notice>startproc: execve (/usr/sbin/powersaved) [ /usr/sbin/powersaved -d -f /var/run/acpid.socket -v 3 ], [ HOME=/ PATH=/bin:/sbin:/usr/bin:/usr/sbin SHELL=/bin/sh RUNLEVEL=3 PREVLEVEL=N DAEMON=/usr/sbin/powersaved ] Starting powersaved: done Starting mail service (Postfix)done Starting CRON daemon<notice>startproc: execve (/usr/sbin/cron) [ /usr/sbin/cron ], [ CONSOLE=/dev/console ROOTFS_FSTYPE=reiserfs SHELL=/bin/sh TERM=linux ROOTFS_FSCK=0 LC_ALL=POSIX INIT_VERSION=sysvinit-2.86 REDIRECT=/dev/tty1 COLUMNS=160 PATH=/bin:/sbin:/usr/bin:/usr/sbin vga=0x31a RUNLEVEL=3 PWD=/ SPLASHCFG= PREVLEVEL=N LINES=64 HOME=/ SHLVL=2 splash=0 SPLASH=no ROOTFS_BLKDEV=/dev/sda9 _=/sbin/startproc DAEMON=/usr/sbin/cron ] done done Starting Firewall Initialization (phase 2 of 2) SuSEfirewall2: Warning: ip6tables does not support state matching. Extended IPv6 support disabled. SuSEfirewall2: Warning: Kernel lacks support for IPv6 REJECT target! Using DROP for IPv6 instead. SuSEfirewall2: Warning: no default firewall zone defined, assuming 'ext' SuSEfirewall2: Warning: no interface active FATAL: Could not load /lib/modules/2.6.27.39-0.2-default/modules.dep: No such file or directory FATAL: Could not load /lib/modules/2.6.27.39-0.2-default/modules.dep: No such file or directory FATAL: Could not load /lib/modules/2.6.27.39-0.2-default/modules.dep: No such file or directory iptables-batch v1.3.8: can't initialize iptables table `filter': iptables who? (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. SuSEfirewall2: Error: iptables-batch failed, re-running using iptables FATAL: Could not load /lib/modules/2.6.27.39-0.2-default/modules.dep: No such file or directory iptables v1.3.8: can't initialize iptables table `filter': iptables who? (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. FATAL: Could not load /lib/modules/2.6.27.39-0.2-default/modules.dep: No such file or directory iptables v1.3.8: can't initialize iptables table `filter': iptables who? (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. FATAL: Could not load /lib/modules/2.6.27.39-0.2-default/modules.dep: No such file or directory ................. LOTS of THESE iptables v1.3.8: can't initialize iptables table `filter': iptables who? (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. done Master Resource Control: runlevel 3 has been reached Failed services in runlevel 3: network Skipped services in runlevel 3: irq_balancer <notice>killproc: kill(1521,3)
From: nomail on 8 Jun 2010 16:21
.....1/ On 06/07/2010 07:03 PM, noi ance wrote: > On Sun, 06 Jun 2010 00:14:55 -0400, nomail typed this message: >> What you're doing is fine, it's just that I gave it up when I got lazy >> and hungry for simple things. At one time I had 8 drives with all of >> them having over a dozen bootable partitions and booting any of them >> from the hd0 mbr :-) > > What I'm asking is what does your /boot/grub/menu.lst look like That only gets written by the system when the installer or a system script installs grub. > Here's mine (default second config but note the root= and resume= > specifications) : > > > default 2 > timeout 8 > ##YaST - generic_mbr > gfxmenu (hd0,0)/message > ##YaST - activate > > ###Don't change this comment - YaST2 identifier: Original name: linux### > title Desktop -- openSUSE 11.2 - 2.6.31.12-0.2 .......... > I'm suggesting the menu specified does not match the physical > connections. Although "/disk/by-id/ata-ST3300620AS_5QF09JXR-part2" is > on my /dev/sdc as /dev/sdc2 it is specified as the boot device. I think > your root= still points to your 500Gb drive, ie, as /dev/sda instead of > the desired 2TB /dev/sdc. > > Not sure how you've specified a root=/dev/sda12 didn't think you could > have that many partitions, or where that partition is located. --------------------------------------------- My currently used grub menu file located on the fat #6 data partition as /boot/user/menu.boo --------------------------------------------- # Grub-0.9x menu file: Dusks AND partitions begin with 0 !! color white/blue yellow/black #color yellow/black white/green #color white/green yellow/black #color cyan/blue white/blue default 0 # default is first entry (starts with 0) timeout 1200 # autoboot in ... seconds ####################### grub screen width scale ########################### title disk 2tb-A file: /boot/user/menu.boo root title all linux systems: visitor login & password "visit", enter "startx" root title Suse-11.2 OP reiser sda1 root (hd0,0) kernel /boot/vmlinuz root=/dev/sda1 vga=0x31a splash=0 3 initrd /boot/initrd title Windows-7 fat32lba sda2 hide (hd0,1) hide (hd0,2) unhide (hd0,1) rootnoverify (hd0,1) makeactive chainloader +1 title Windows-XP fat32lba sda3 hide (hd0,1) hide (hd0,2) unhide (hd0,2) rootnoverify (hd0,2) makeactive chainloader +1 title Suse-103 OP reiser sda7 root (hd0,6) kernel /boot/vmlinuz root=/dev/sda7 vga=0x31a splash=0 3 initrd /boot/initrd title Suse-111 & NEXT reiser sda8 root (hd0,7) kernel /boot/vmlinuz root=/dev/sda8 vga=0x31a splash=0 3 initrd /boot/initrd title Debian-5 Gnome OP reiser sda9 root (hd0,8) kernel /boot/vmlinuz root=/dev/sda9 vga=0x31a splash=0 3 initrd /boot/initrd ##################################################################### title Suse-112 STERILE DISCONNECT!! reiser sda10 root (hd0,9) kernel /boot/vmlinuz root=/dev/sda10 vga=0x31a splash=0 3 initrd /boot/initrd title Suse-103 STERILE DISCONNECT!! reiser sda11 root (hd0,10) kernel /boot/vmlinuz root=/dev/sda11 vga=0x31a splash=0 3 initrd /boot/initrd title Suse-111 STERILE DISCONNECT!! reiser sda12 root (hd0,11) kernel /boot/vmlinuz root=/dev/sda12 vga=0x31a splash=0 3 initrd /boot/initrd title Debian-5 STERILE DISCONNECT!! reiser sda13 root (hd0,12) kernel /boot/vmlinuz root=/dev/sda13 vga=0x31a splash=0 3 initrd /boot/initrd # 640x400 640x480 800x600 1024x768 1152x864 1280x1024 1600x1200 # 4 bits | ? ? 0x302 ? ? ? ? # 8 bits | 0x300 0x301 0x303 0x305 0x161 0x307 0x31C # 15 bits | ? 0x310 0x313 0x316 0x162 0x319 0x31D # 16 bits | ? 0x311 0x314 0x317 0x163 0x31A 0x31E # decimal | d785 d788 d791 # 24 bits | ? 0x312 0x315 0x318 ? 0x31B 0x31F # decimal | d786 d789 d792 # 32 bits | ? ? ? ? 0x164 ? ----------------------------------------- Below that is the grub2 menu file from one of the Debian partitions that offer it. I had this set up just so I could start warming up to grub 2. It is not in use. ------------------------------------------- # # # Grub2 menu file: partitions begin with 1 !!!!!!!!!!! # Standard location is /boot/grub/grub.cfg # # # Don'tforget to park copy in all /boot/grub # # set default=0 # default is first entry (starts with 0) set timeout=1200 # autoboot in ... seconds set menu_color_normal=cyan/blue set menu_color_highlight=white/blue menuentry "Debian Experimental grub2 reiser part-2" { set root=(hd0,2) linux /boot/vmlinuz-2.6.26-1-686 root=/dev/sda2 ro initrd /boot/initrd.img-2.6.26-1-686 } menuentry "Debian Experimental grub2 (single) reiser part-2" { set root=(hd0,2) linux /boot/vmlinuz-2.6.26-1-686 root=/dev/sda2 ro single initrd /boot/initrd.img-2.6.26-1-686 } menuentry "Windows-XP fat32lba part-3" { set root=(hd0,3) } menuentry "Debian 5.0.0 Operational reiser part-6" { set root=(hd0,6) linux /boot/vmlinuz root=/dev/sda6 splash=0 3 initrd /boot/initrd } menuentry "Debian 5.0.0 Fix & Test reiser part-7" { set root=(hd0,7) linux /boot/vmlinuz root=/dev/sda7 splash=0 3 initrd /boot/initrd } menuentry "Debian 5.0.0 STERILE reiser part-8" { set root=(hd0,8) linux /boot/vmlinuz root=/dev/sda8 splash=0 3 initrd /boot/initrd } # with this species we'll again have to standardize using actual # kernel and initrd copies (no links) anywhere except where the # system also writes its thingies menuentry "Suse 11.1 Operational reiser part-9" { set root=(hd0,9) linux /boot/vmlinuz root=/dev/sda9 splash=0 3 initrd /boot/initrd } menuentry "Suse 11.1 Fix & Test reiser part-10" { set root=(hd0,10) linux /boot/vmlinuz root=/dev/sda10 splash=0 3 initrd /boot/initrd } menuentry "Suse 11.1 STERILE reiser part-11" { set root=(hd0,11) linux /boot/vmlinuz root=/dev/sda11 splash=0 3 initrd /boot/initrd } ############## # title Windows-1 (for p2p) sda1 #lock hide (hd0,0) hide (hd0,1) hide (hd0,2) hide (hd0,4) hide (hd0,4)################## grub boot menu ############### color white/red white/black #color yellow/black white/cyan #color white/green white/black #color white/blue default 0 # default is first entry (starts with 0) timeout 1200 # autoboot in ... seconds ####################### grub screen width scale ########### hide (hd0,5) hide (hd0,6) unhide (hd0,0) unhide (hd0,4) rootnoverify (hd0,0) makeactive chainloader +1 # title Windows-2 (internet) sda2 #lock hide (hd0,0) hide (hd0,1) hide (hd0,2) hide (hd0,4) hide (hd0,5) hide (hd0,6) unhide (hd0,1) unhide (hd0,4) unhide (hd0,5) rootnoverify (hd0,1) makeactive chainloader +1 # title Windows-3 (workshop) sda3 #lock hide (hd0,0) hide (hd0,1) hide (hd0,2) hide (hd0,4) hide (hd0,5) hide (hd0,6) unhide (hd0,2) unhide (hd0,4) unhide (hd0,5) unhide (hd0,6) rootnoverify (hd0,2) makeactive chainloader +1 # title Debian 40r1-a64 ext3 sda9 root (hd0,8) kernel /boot/vmlinuz-2.6.18-5-amd64 root=/dev/sda9 vga=0x31a splash=0 3 ro initrd /boot/initrd.img-2.6.18-5-amd64 # title Suse 103-i586 LAST reiser sda10 root (hd0,9) kernel /boot/vmlinuz root=/dev/sda10 vga=0x31a splash=0 3 initrd /boot/initrd # title Suse 103-i586 ON hd2!!! reiser sdb10 root (hd1,9) kernel /boot/vmlinuz root=/dev/sdb10 vga=0x31a splash=0 3 initrd /boot/initrd # title Suse 11.0-i586 NEW reiser sda11 root (hd0,10) kernel /boot/vmlinuz root=/dev/sda11 vga=0x31a splash=0 3 initrd /boot/initrd # title Suse 11.0-i586 STERILE reiser sda12 root (hd0,11) kernel /boot/vmlinuz root=/dev/sda12 vga=0x31a splash=0 3 initrd /boot/initrd # #...1/ |